Clever Over-the-Door Kill Point

When you hang wallpaper on all four walls of a room, you get to the point where your last strip meets up with the first strip you hung. We call that the kill point. That last strip gets split vertically in order to bridge the width of the distance to meet up with the first strip. The cut-off part gets thrown away. This virtually always results in a pattern mismatch in the corner where the first and last strips come together. So, when possible, you hide this mismatch in a corner behind a door, or somewhere else that is not noticeable. But in this powder room, ALL the corners were out in the open and very visible. But I think the corners look better when the pattern matches exactly, as shown in this photo.

But there is still going to be SOME point in the room where the last strip meets the first strip – and where the pattern will not match. I chose the least conspicuous place in this room – over the door. After all, not many people spend much time looking 10′ up over a door that’s behind them. Still, a pattern mismatch here would be very noticeable; maybe more broken up and obvious than in a corner. But I had a plan …

Moving from right to left, I plotted where my next strip would fall. The sequence of “high” and “low” maps at the ceiling line was in sync with the strips on either side. But I’m going to end up with a 5 1/2″ gap on the left side. Since the figures / maps were about 8″ wide, cutting one down to 5 1/2″ wide would distort it too much. So instead I decided to “grow” the white areas in between the map figures.

I could do this because there were “stripes” of white areas in between the maps that were uninterrupted from top to bottom; if there had been a motif that crossed horizontally, this would have been much more difficult. I took that strip of wallpaper slated for over the door and slit it vertically along the “empty” white area into three parts.

Then I took some scrap paper from the waste pile (always buy a little extra paper!) and used my straightedge to trim off slices that had no printing on them. Each of these ended up being only about 1″ wide. I was looking for about 6,” so I made six slices, plus one more for good measure. Because these slices were all white, and because the backing was also white, I put a pencil mark on the back side, so I could tell which side to put the paste on. Because the paper was thin and somewhat transparent, I had to remember to make my marks lighter than usual. Going back to the third photo, you will notice a tiny bit of ink on the far left edge of the piece mocked up above the door; I used my straightedge to trim off this 1/4″ wide area, too.

Here is how the all-white strips would be placed in between the printed sections. In actuality, each gap took two 1″ strips, not the single one shown in the photo.

Here is the first printed section going in next to the strip to its right. I couldn’t use a 1″ strip in between these two because there was a tad of pattern that had to be matched between the two strips, due to various logistics. But I could add two of the 1″ strips to the left of the new printed section, as shown here. Moving to the left, I did that two more times, with two more sections and two more sets of 1″ wide strips. At the last juncture, I did do a vertical overlap of the excess 1/2″ resulting from the gap of 5 1/2″ and the six 1″ wide fill-in strips. I could have done a double-cut (splice), but the strips were awfully narrow to work with, I wanted to avoid scoring damage to the wall, and the overlap would be obscured by the vertical elements in the pattern motifs. Plus, it was 10′ up, after all.

Here is the finished look. The seams will be less visible once the paper is dry. The three spaces between these three map motifs are 2″ wider than the spaces between the maps around the rest of the room. But the difference is virtually undetectable. And, like I said, who’s looking way up there, anyway? And … it’s a whole lot more attractive than the other option – of having a pattern mismatch running the entire 10′ height of a corner in the room.

The pattern is “City Maps” and is by Rifle Paper, which is made by York, one of my favorite brands.

Tags: city maps, corners, double cut, kill point, mismatch, paste, rifle paper, splice, straightedge, transparent, wallpaper, York