Dining room in the Oak Forest area of Houston, before. All white and crisp – but bland .Here with just a touch of color and texture . The homeowner took my suggestion to use an embossed vinyl faux grasscloth product, which is very consistent in color . The problem with real grasscloth is that so very often there are disappointing color variations between strips , even if they come off the same roll . We call this shading and paneling . Do a search here to see previous posts about this. Note that with both materials you will see the seams. With this faux material, once you got 3′ away, you can’t see the seams at all. The paper along the top of the wainscoting chair rail is to prevent my wallpaper primer from splattering onto the molding . I do the same for baseboards and bathroom backsplash es .Opposite corner done. Close-up showing the realistic texture of the vinyl product .This is by Designer Wallpapers and was purchased from the Sherwin-Williams in the Rice Village , by Dorota , who has been selling wallpaper for 25+ years and is THE expert on helping you select your perfect pattern .
Before, primed and ready for wallpaper . Just about everything in this house is white – walls , furniture , accessories . Serene, but kinda blah.The homeowner wanted to add a pop of color and chose the powder room to be the fun room . I love the way the pattern seems to push the walls away and makes the room look larger . In addition, the strong vertical element of the tree trunks adds a lot of energy to the space. I love the burnished gold fixtures with the green paper . This very popular wallpaper pattern is called Raphael and is by Sandberg . It comes in a lot of colors – I’ve done a bunch of them! This is made in Sweden and is a non-woven material , also called paste the wall . It is more durable and breathable than traditional papers, and will hold up nicely in a bathroom . The home is in the Oak Forest area of Houston . installer installation
Obviously, this manufacturer has had complaints about their product. So they’ve come up with a CYA paragraph(s) designed to throw blame onto the wallpaper installer. Only thing is, most all of the above points they are trying to dodge ARE the fault / responsibility of the manufacturer – NOT the paperhanger . Gaps: poorly trimmed paper at the factory, possibly due to dull or wobbly trim rollers . Raised edges: poorly trimmed edges, or incompatible inks and substrates. Blisters: Usually due to off-gassing due to surfaces that don’t breathe and therefor trap moisture. Or to inks and substrates that are incompatible. … The substrate absorbs moisture from the paste and stretches , but the inks do not, resulting in wrinkles , warps , waffling , and / or quilting . But, hey – instead of doing some research and product development to improve our wallpaper , let’s just blame it on the paperhanger .
I have no idea what’s going on here, but it happens from time to time. I had been rolling on wallpaper primer in two rooms for a few hours . I’m suspecting I held a tool in a certain way for a long time , or somehow blocked circulation to a part of this finger . It doesn’t hurt , but it is a little swollen. The color got darker and lighter during the rest of the day. I did some shopping on the way home, and the store was cold , and that seemed to exacerbate the issue – finger got cold and numb and really purple . Back at home in my nice warm home office , it’s still discolored , but not as much.
I hate seeing little speckles of paint on people’s floors or moldings . This happens when tiny splatters of paint fly off the roller cover . Sometimes the operator is just moving too fast , but some paints are thinner and prone to splatter than others. You can Search here to find pictures of what I’m talking about. To prevent my wallpaper primer from landing on the floor , baseboards , backsplash , or, as in this case, wainscoting , I first cover the floor or vanity with dropcloths . Next I use these strips of thin , flexible , plastic-backed paper dropcloth material to cover anything that the dropcloths can’t reach. I use push-pins to hold them in place. I cut these strips from larger dropcloths. 8″-9″ wide seems to be about right to protect most baseboard heights and other surfaces , such as this chair rail wainscoting in a Houston Heights dining room . Once I’ve rolled primer on the wall above, I remove the protective strips and use an angled trim brush to cut in the primer along the top edge of the molding . wallpaper installer
This young couple hosts the mother / mother-in-law a few times a year, and are lucky enough to have a private spare bedroom for her. To make it special, they wanted to jazz up the area a little. Enter this fun and whimsical wallpaper pattern .The room before was a pretty shade of murky teal – but needed personality and warmth. The wall started out with a light orange peel texture . I skim-floated the wall, and then sanded it smooth . Along the baseboard at the floor , here’s the dust from sanding , along with the sanding sponge I use – this is a modern take on the idea of wrapping sandpaper around a block of wood . I tack painter’s plastic across the wall from ceiling to floor to prevent dust from getting into the room or onto the furniture . Here’s the wall smooth and primed , ready for wallpaper . Since this is a dark wallpaper and I want to be sure that the white wall does not peek out from behind the seams, I stripe dark paint along the wall under where the seams will fall. Because non-woven papers don’t expand when wet with paste , it’s simple to measure the width of your strips and plot out where each seam will fall. Use the laser level as your guide . Do a Search here (upper right hand corner) to read more about this technique. I use craft paint from Texas Art Supply (or any hobby store ), diluted with water from a Gatorade bottle cap , and applied with a scrap of sponge . Further insurance is taking a chalk pastel (never oil pastel – oil bleeds and will stain wallpaper) and running it along the edge of the wallpaper strip – from the backside to avoid staining the surface – to cover the white substrate the wallpaper is printed on. This is to prevent white from peeking out at the seams , which can happen with dark papers. Centering the first strip in the middle of the wall, and using my laser level to ensure the strip is nice and straight and plumb . Note: The strip is not centered on the wall. The dominant pattern element is. Notice that the center of the dominant pattern motif – the white circular flower – is 3.5″ to the right of the left edge. This means that I had to position the left edge of the wallpaper 3.5″ to the left of the center of the wall, in order to get the round white flower to fall down the center of the wall. When you look again at the finished photo, you’ll notice that the white flower falls down the middle of the walls, and that it also appears at equal distance from both the right and left walls. Most people wouldn’t be able to put their finger on this symmetry , but it is something they subconsciously notice , and it lends a feeling of orderliness to the room. As orderly as you can be, that is, with pigs dancing around the meadow dandelions ! Finished accent wall . The three other walls painted in blue were a bit of a surprise, because one would think the more dominant color of green would be used. But with so much green in the wallpaper, green on the walls, too, would have been too much, perhaps. I like the cool feeling that the blue creates . There is plenty of the exact same blue in the wallpaper pattern to tie the walls and wallpaper together. Close up shows the stamped printing technique . You’ve gotta love a frolicking pig in a hand-knitted sweater! This pattern is called Hoppet Folk and is in the Wonderland line by Borastapeter , a Scandinavian company . It’s a nice, sturdy but flexible non-woven material that can be hung via the paste the wall installation method . In addition, this product will strip off the wall easily and in one piece , with no damage to your walls, when it’s time to redecorate. This is a very popular pattern, and I’ve hung it more times than I can count, just in the last two or three years. It does come in other colors – but most people gravitate toward this black version. The townhome is in the Rice Military area of central Houston .
You’re looking up at the bottom edge of crown molding , where the painter let his brush cover the surface with flat orange wall paint. Gee, to me, beautiful molding is elegant and elevates the appearance of the whole room. It would look so much nicer to have that edge painted white like the rest of the molding. A painter who’s either too lazy or unskilled to ” cut a clean line ” between the wall and the woodwork .
Wallpaper looks better and will have fewer wrinkles and relief cuts , plus there will be fewer cut edges to come loose, when it goes behind objects like switch plates and this thermostat. Here it was a matter of gently pulling off the glass front of the Nest thermostat, then removing two screws on the mounting bracket. I left it connected to the wires in the wall, but pulled the wires out further from the wall so there was more play to work around. I was able to place the wallpaper over this area, cut an “X” where the thermostat was, and then pull both the thermostat and the back plate through the wallpaper. Note: I wrapped the thermostat in plastic before starting, to protect it from wallpaper paste / adhesive . Then put the backplate in place, reattach the thermostat, and then replace the glass front. Smooth the wallpaper into place. All looks perfect!
Window wall before. Due to the logistics of plotting and hanging grasscloth, this one wall took me six hours. More on that in a separate post.Finished wall with drapes replaced. The drapes compliment the slight sheen of the grasscloth material. How elegant ! Below the windows.Below the windows .Rounded bull-nosed edges on this entry arch . The edges are always tricky to wallpaper . Arch done. East corner. I stripe the wall with dark paint to prevent the white wall primer from showing in case of tiny gaps at the seams . The southwest corner had an odd angle in it, probably due to the powder room or stairs or maybe A/C ducts on the other side of the wall. The light hits that one angled wall differently. This photo also nicely shows the fine texture of the grass material, and the subtle sheen . Also note that the seams in grasscloth are always visible . So good installer will take care to plot so the panels are placed in the most pleasing manner – in this case, down the center of the wall to the left. This does eat up a little (or a lot) of extra paper – the rolled up scraps you see are leftovers from this process. They can’t be used anywhere else, so will be thrown away . Planning all this is another reason to have the installer figure how many rolls / bolts are needed. Purchasing based on square footage would result in an unbalanced panel layout . Northwest corner. Grasscloth often has shading or paneling ( color differences ) between strips. This particular grasscloth was amazingly homogeneous in color, and I was very pleased. In fact, over this entry to the home office was the only place where there was any noticeable color difference at all. (also visible in previous photo) Unfortunately, I don’t know the brand . But I suspect that a lot of grasscloth and other such natural materials are made by the same manufacturer – just sold under different brand names . The home is in the West University area of central Houston .
Grasscloth is a natural material that cannot be matched from strip to strip, so all the seams will be visible . In addition, there is usually a slight but noticeable color difference between strips / panels (called shading or paneling ) . So it’s important to plot the layout of the strips to give the most visually pleasing overall look. Usually this means balancing the width of strips so they are all equal , at least on the same wall . We call this engineering . This wall presented particular challenges , due to the widths of the elements. Grasscloth comes 36″ wide . You can use your straightedge and a sharp razor blade and trim it down to any width you want. The width of both the large wall spaces to the right and left of the bank of windows was 34.” The width of each window was about 35.” The width of the two spaces in between the windows was 7.” So you’d think I could trim my panels on either side of the windows, and then over the windows, to about 34″-36″ – give or take a few inches (or fractions thereof). But that would leave me with two 7″ wide strips between these 35″ panels. Although the look would be uniform and mirror-image from the center outward, moving from right to left you’d have: 35,” 35″, 7,” 35,” 7,” 35,” 35,” … those 7″ breaks were just not going to look right. One option was to determine the width of the wall (189″) and make each strip an equal width. This worked out to six strips, each at 31.5″ Not good, because this would mean a seam down either far side. And since those sides were 34″ wide, that would mean a 31.5″ wide strip and a strip 2.5″ wide. Not attractive at all, and it would use up an extra strip of wallpaper. This six strips @ 31.5″ wide scenario might also land with a seam smack in the middle of those 7″ wide interludes in between the windows. Not attractive at all. So I decided to make the two outer strips 35″ wide. That left 119″ of wall space above the windows to be covered with wallpaper. Do some math and you get four panels of 29.75″ wide. This gave a balanced and uniform look to the area over the windows, and also prevented seams from landing between the windows. Moving right to left, I cut and hung the full length outer strip first. Then I cut and hung the strip over the window on the right. Then I measured to find the centerpoint of the window in the middle. Turns out it was a bit less than 29.75″ away. So I trimmed that next over-window strip accordingly. Once that was in place, I measured from that center point above the middle window out to where my left full-height panel would fall, 35″ out from the wall. Took the resulting measurement and divided by 2. Lo and behold, each of the next two panels over the window was going to be a bit wider than 30.” No problem. No one (but a paperhanger or maybe an engineer) is going to notice a 1/4″ or even a full 1″ difference in widths between this strips over the windows. Another thing to point out … it’s important that I took measurements before cutting these strips for this second left-hand section. Because, since grasscloth comes at 36″ (and walls can be wonky), if my strips had been narrower (say, 28″), that last full-height panel on the left might have ended up needing to be 37″ wide – and that wouldn’t work because it only comes 36″ wide – plus you need at least 1/8″ to wrap around the corner. Luckily I had the flexibility to be able to trim the panels over the windows to any width needed, to accommodate all this. If you’ve followed all this so far, let me also toss in that we also need to figure how to get paper in between those windows. More on that below. In this scenario, I’m moving from right to left. Area beneath the windows needs to be treated in the same way, and preferably with widths that match what’s going on above the windows. In addition, it’s tricky because after you move across 12′ of wall space, the strips above and below the windows are going to twist and torque out of shape, so that last full-length panel on the far left might not butt up perfectly with the last strip under the windows. The grasscloth is black , and my wallpaper primer is white . It’s common for teeny gaps to appear at the seams . In this case, it’s likely that white wall would peek out from those gaps. So I like to stripe under where the seams will fall with dark (diluted) paint . This takes measuring , plotting , and also a heat gun to get the paint to dry before the wallpaper hits it, to avoid staining. You can do a Search here to read more about this technique . Now let’s talk about getting wallpaper in between those windows. As you can see in the photo, if I hang a 30″ wide strip, a whole lot of paper is going to be cut off and thrown away. Also, a whole lot of sticky, pasted paper is going to bump against that window molding and maybe even the window glass. A lot to clean up! And unwieldy, to boot. My solution was to stop the wallpaper just a little below the tops of the windows. Then I would patch in a 7″ wide strip in between the windows. This is trickier than it sounds, because, if it were a paper wallpaper, I could simply cut along a design motif and overlay the 7″ wide piece. But grasscloth is thick and overlaps don’t look good. Also grass has no design elements , and the reeds of grass don’t necessarily fall perfectly horizontal , and even if you cut everything perfectly true to square , if the window molding is a teeny bit off-plumb , then your edges won’t butt up perfectly. So that’s a good reason for striping the black paint under where the butt join will occur. Same thing for the sections under the windows. I measured and positioned the strips so that the top edge (which I had trimmed to be perfectly horizontal) fell between the narrowest part of the windowsill molding, for less visibility. I admit, instead of butting the two pieces, here I did overlap the 7″ wide strip about 1/4″ onto the piece under the window, right at that narrow junction. It’s only about 3″ wide, and I figured no one is going to be examining it that closely, anyway. This saved me about a half an hour of measuring, trimming, testing, repeat, repeat. This is my second window interlude, and by this time I had realized that it’s hard to trim stiff grasscloth around intricate moldings precisely . So I used paint to fill in the edges around the window molding, just in case there might be any gaps between the grasscloth and the molding, so you would see black instead of the white molding paint. I did this with a small sponge; if I had used an artist’s brush it would have been a bit neater and tighter to the conforms of the molding. But sometimes you’ve gotta relax and realize that no one’s going to be scrutinizing the insides of moldings below shin-level. Area over windows finished, with drapes back in place. Turns out this particular grasscloth is so uniform in color (quite unusual, I will add), that you can’t really see the panels , nor their equal widths , anyway. I’m still glad I took the time to do all this math and trimming. Area below the windows, done. That last seam on the left bears some explanation, too. Moving across the top of the windows, I measured that that last strip – the full-length strip – would need to be exactly 35″ wide. It butted up nicely to the last strip above the windows. But, due to twisting , shifting , expansion , unlevel and unplumb walls and ceilings , and other factors, there is a really good chance that that last 35″ wide strip would not butt up perfectly with the last 30″ wide strip under the window . So I planned to splice these last two strips together. Yeah, the drapes are hanging there, I coulda overlapped the two strips about 1/2″ and the drapes would have covered it. With a thin wallpaper, I probably would have done this. But grasscloth is thick, and an overlap would be visible , and also the adhesive / paste can’t be trusted to adhere as well to grass as it would to paper . So I plotted for a splice. Instead of trimming my last strip under the window to 30″ (read above), I trimmed it to 32″ wide. That way, when I hung the last full-length strip to the left, which was 35″ wide, it overlapped the piece under the window by a few inches. Then I did a double cut and spliced the two pieces. See below for details about that technique. Grasscloth is 36″ wide, and this wall area is wider than that. So two strips were needed. This means you’re going to have a seam, and since grasscloth seams are always visible, it looks best to plot to have the seam fall down the center. It uses more wallpaper to do this, but it looks much better than having, for example, a 36″ wide strip next to an 8″ wide strip. As mentioned above, in case you get thin gaps at the seams, a dark stripe of diluted craft paint under where the seam will fall, will prevent white wall from showing through. Rounded / bull-nosed edges and corners have been popular in new construction for at least 10 years. I wish they’d go away. They’re very difficult to trim around, and hard for the paper to conform to and adhere to. It’s very hard to trim around that rounded edge, because the paper is hanging over and blocking your view, because grasscloth is thick and stiff and your fingers can’t feel through it, and because the edges aren’t necessarily true and plumb so a laser level or other level won’t help you much. I use this little gadget as a trim guide. It’s actually a small section of the same corner bead material that drywallers use when they assemble these walls. Cut to about 1″ long and notched in different places where you might trim along the edge of the wall. It’s intended that you place your trimming knife in one of the notches and slide the gizmo along the edge and make your cut. I find that awkward and also inaccurate. So I prefer to use the notches as a guide and mark where I plan to trim with a pencil. Since this wallpaper is black, I used this marking pencil from my home sewing kit instead. Chalk might work, but I was afraid it might now wipe off completely. The pink pencil line was barely visible, but it was enough for me to use a scissors to trim along the grasscloth. I like this better than using a razor blade as I can see better, and also less chance of scoring into the primer or wall. Which raises its own set of issues – do a search here to find previous posts.Inside view of the trim guide. Finished arch. Note the four panels of equal width above the arch. And two flanking full-height panels also the same widths. I was lucky that there was no pattern to match, so I was able to butt my two flanking strips right up to the edge of the bull-nosed corner. No trimming needed! Then I measured the remaining width between these two strips (the area over the arch), divided by four, and cut four strips of equal widths. I hung the two on the left, and then one on the far right. This left one strip still to be positioned to the right of center. So the pieces are going to meet over the arch, rather than the last strip falling in a corner. Same as the last strip under the window (discussed above), it’s really difficult to get your last piece to fit in here perfectly. I’ve done it, but it takes a lot of measuring, trimming, testing, retrimming, and often starting all over again. So I did a double-cut / splice. A double cut involves cutting each strip an inch or so wider than it should be, and overlapping the two. Then you take a straight edge and sharp razor blade and cut through both layers. This handy tool is a wonderful non-slip guide for this process. It was invented by an installer colleague in the Wallcovering Installers Association ( WIA ) and she has them fabricated in various lengths (along with other cool tools ) and sells them on-line. Contact me if you’re interested. Anyway, it takes a lot of strength to cut through two layers of grasscloth, so somewhat difficult for lil’ ol’ me. You also want to be sure to not cut / score into the wall, because the tension of drying wallpaper can tug at the wall and cause it to actually come apart, leaving an open seam that’s difficult to repair. So you’ve got to put some padding under the wall where the cut will take place. I use special strips of polystyrene (hard but flexible plastic) to pad the wall. Also invented by a colleague in the WIA , who also sells other cool tools and supplies. Contact me if you’re interested. This black grasscloth was printed on a white substrate. If the seams aren’t absolutely tight, there can be worries about the backing showing through to the front. So sometimes we’ll take a piece of chalk or pastel (never oil pastel or permanent markers because they bleed and stain ) and run it along the edge of the paper – from the back, and taking care to not get chalk on the surface. I do this frequently with dark papers ( do a search here to see previous posts ) but opted not to do it with this grasscloth. It wasn’t necessary, and might have stained the porous reeds of the grass. It was beneficial, though, to have striped dark paint on the wall under the seams, as mentioned above. Ugh. Grasscloth comes 36″ wide, and this section of wall is 38″ wide. It’s not visually pleasing, nor is it easy from an installation point of view, to have a 36″ wide strip next to a 2″ wide strip. Or to use scraps and put a 25″ wide strip next to a 13″ wide strip. So best to plan two strips of equal widths. Two strips, each 19″ wide, with the seam down the middle. Actually, the strip on the left was 19″ wide, but I trimmed the strip on the right to 21″, because I like the wallpaper to extend 2″ over the top of the door molding. This provides a more stable surface in case of shifting foundation or walls, and less likelihood (knock on wood) of the seam opening up should the house / drywall experience shifting. Note that design “rules” caution against seams down the middle of spaces. But it would have been more visually distracting (and used up more paper) to have made three strips of each 12.75″ wide. And would have looked even dumber to have used scraps left from other walls and put together two strips of disparate widths. So the homeowner and I discussed during our initial consultation , and she was happy with the center seam. Once it was all finished, this particular grasscloth was so even in tone that you barely see the seams, anyway. Win-win! This did use up additional paper, though, as noted in a previous photo above.
The Wallpaper Lady's Blog 