I hung this paper in a little boy’s bedroom about two years ago. Now a new baby is coming, so Son #1 is moving from the nursery to his “Big Boy’s Room” next door. In the process of the shuffle, the parents had the connecting Hollywood bathroom updated, and this involved moving a door – which meant messing up the wallpaper.
As you can see in the top photo, instead of taking the time and effort to remove the wallpaper, the workmen put their patching compound right on top of it. I don’t like hanging paper on top of paper, for many reasons. There are adhesion issues. And also, for one thing, it’s not good to have seams fall on top of seams. For another, because the new paper is somewhat thick, you would have a visible ridge from top to bottom along the edge of the new strip.
So I took a razor knife and cut roughly around the workmens’ patch. Then I stripped off the paper around it, up to the edge of the adjoining strip. I did this on both sides of the corner.
This wallpaper is of a non-woven material, and is designed to strip off the wall easily and in one piece when it’s time to redecorate. I was pretty disappointed that that turned out to not be the case.
On the other hand, I was happy that it didn’t. Stripping paper that way puts a lot of stress on the wall surface, and you can end up with delamination (coming apart) of various layers under the paper (primer, skim-float, paint, drywall).
So I used a more labor-intensive, but lower-impact method. Click my page to the right for more info on the process. I first stripped off the top, inked layer of paper. That left the white backing still adhering to the wall. I used a sponge to apply plenty of water to this backing. The idea is to reactivate the paste that is holding it to the wall. Once that paste was wet enough, the backing pulled off the all cleanly and easily.
I was really pleased that my primer from the original install held up perfectly under all this soaking and tugging. I had worried that it might “rewet” and pull away from the wall, which had been my experience with it before. I had used Gardz, a penetrating product designed to seal torn drywall. It’s also good at sealing new skim-coated walls. And wallpaper sticks to it nicely, so all the better!
One photo shows you the stripped off area next to the edge of the remaining strip. You can see the thickness of this existing strip. The new wallpaper will butt up against this, and there will be no ridge because the thicknesses of both strips are the same.
Another photo shows my stripped-off area next to the contractor’s patched area. There is a difference in height between the newly revealed wall and the patched area – and that will show as a ridge or bump under the new wallpaper.
To eliminate that difference in height, I skim-floated over the area. In one photo, you can see the wet (grey) smoothing compound. I set up a strong floor fan to assist in drying. My heat gun also came in handy.
Once it was dry, I sanded it smooth. Now you don’t see any transition between the newly exposed wall and slightly higher patched area. I applied Gardz to the all the newly patched areas. Set up the fan again. And once it was dry, I put up the replacement paper.
It’s a good thing the family had paper left over from the original install. If they had had to purchase new paper, it could have come from a new Run (slight difference in color shade), and that would have meant stripping off and replacing three walls.
We had barely enough paper. The corner was out of plumb by as much as 1/2″ from floor to wainscoting, on each side of the corner. That adds up to an inch out of whack. That one inch meant we needed a whole new strip of wallpaper, to get the paper on the wall to the left to match up with that on the wall to the right.
Long story short, the whole thing turned out great. There is a bit of a mis-match in that corner, but it’s not very noticeable at all.
The wallpaper is by the Scandinavian company Boras Tapeter.
The home is in the West University neighborhood of Houston.
The Wallpaper Lady's Blog 