This Brooklyn Toile wallpaper by Flavor Paper on an accent wall in a nursery went up beautifully. The contractor had added new Sheetrock to one wall, and painted the other, old/original wall. I skim-floated both walls and sanded smooth, primed, and hung the wallpaper. Perfect! (Search here to see my original post.) But within less than a month, the homeowner contacted me and said that the wallpaper was ” coming off the wall .” It was a 1920’s bungalow in the Woodland Heights neighborhood of Houston. And therein lies the brunt of the problem. The wallpaper itself is not ” coming off the wall .” What’s happening is that the wall surface itself is coming apart – or, delaminating . This is because multiple layers of paint and other substances on the wall may not be compatible. A probably scenario: In 1920 oil-based paint was used. Later someone rolled on a coat of latex paint. Then the homeowners redecorated and used gloss paint. Then some ” flippers ” who had watched too much HGTV slapped on more paint without bothering to de-gloss or prime first. And somewhere in the mix you’ve got cheap paint and dust and other incompatible materials.Over time, and especially when stress is put on the wall surface, such as when wet wallpaper paste dries and the paper shrinks, this stress can tug at the wall and actually pull these layers apart. There are other contributing factors, too, such as humidity, temperature, and location. I find it interesting that the worst parts of the affected seams were toward the top of the wall. This speaks of heat, humidity, and forced air (either hot or cold) coming out of the air vent just to the right of this wall. This photo is of the area over a door, very close to the air vent. See how thick that is? It’s not just the wallpaper. There are several layers of wall coming apart. Some layers are clinging to the back of the wallpaper, and some are staying stuck to the wall. Multiple layers, many years of coatings on this wall. Easy to see the many layers. The paper itself, my blue primer, my layer of smoothing compound, paint, more paint coming off the wall. Then multiple layers of paint and texture still clinging to the wall. This shot is just below the ceiling.Same thing happening at the baseboard at the floor. Layers of paint separating from the wall in chunks. Some pulled off easily, and some I had to chop off with my 3″ putty knife.Most of the paint and unstable surface material clung to the back of the wallpaper. This pile is just three strips – only half the wall. But it’s thick and stiff and heavy because of the paint stuck to the back of the wallpaper. There was so much and it was so heavy and bulky that I had to carry it out to my van in two trips. When I got home, it totally filled my trash bin. Here’s the wall once all the other layers came off. Brushing my hand over it revealed a layer of dust. No wonder the paint and other coatings wouldn’t stick. Nothing sticks to dust. It’s like flouring a cake pan… The paint or wallpaper will kinda stick – but won’t really stick. Paint on top may be fine. But add a little stress from drying / shrinking wallpaper, and you may end up with layers that pull apart. Wiping the walls with a damp sponge removed a lot more dust. But the wall still felt chalky. Whatever type of paint this was, it was not holding together. I had to stabilize this chalky surface. Enter Gardz, a wonderful product – Gardz is a thin, penetrating sealer that soaks into porous surfaces and binds substances together. It dries hard and creates an intact surface. The darker area in the picture is where I’ve rolled on a test area. Gardz is thin like water, and it runs and drips and splatters. It’s imperative that you cover floors, countertops, and baseboards, and roll carefully, and roll upward rather than downward, to minimize runs and drips. A microfiber roller holds the liquid well, and reduces drips. Gardz is made by Zinsser. No photo of the finished wall, but I was very pleased with the stability of the surface. No more chalk or dust. Now, there still could be unstable or incompatible layers deeper inside the wall. (Latex paint over oil without proper prep.) But for now I feel pretty confident that this wall is solid and will hold up to the next process in preparation for getting the new wallpaper up.
These nails were holding picture hooks to the wall. The hooks had an adhesive backing. When they were removed from the wall, chunks of latex paint stuck to them and pulled away from the wall, revealing a crumbly sub-surface. This is bad news for wallpaper that might be hung on top of this.Other spots. What happens is, this is a 90 year old house. Over the years, many coats of paint and other surface treatments have been applied to the walls of this dining room. These coatings are not necessarily compatible with each other. Plus they may have been applied without the proper surface preparation. Oil based paint, then latex, then someone rolls on a gloss paint, the next guy follows with latex but neglects to de-gloss the previous layer so the new layer doesn’t really stick well.Somewhere along the line, something got chalky. Here you see I have wiped crumbly chalky substance from inside the wall. This is why the latex paint is not adhering well and pulled away so easily. Nothing sticks to dust or grit or chalk. Gardz is cool stuff. It’s a penetrating sealer that soaks in and actually binds crumbly materials together, drying into a hard, solid mass. The problem here is, it won’t penetrate the paint that is on top of the unstable layer, so we’re still dealing with a wall that has potential to come apart (delaminate). Gardz applied. You can see how it has soaked into the porous areas, but is sitting on top of the latex paint.
The problem with an unstable wall and wallpaper, is that, as wallpaper sits on a wall and the paste dries, the paper shrinks just a tad, and this shrinking puts tension / torque on the wall beneath it. Sometimes this is actually powerful enough to pull the layers inside the wall apart, resulting in seams that split open.
These are not “loose seams,” but the paper actually taking layers of paint and dust along with it. Really can’t be repaired.
So best to find a way to prevent it from happening in the first place. More on that later.
Textured walls have been smoothed and primed. Ready for wallpaper!The design looks as if it were sketched on with artist’s chalk.
Grey, tan, white, and cream are very popular colors these days, so this wallpaper suites the modern vibe of this newly updated home in the Willowbrook / northwest area of Houston.
Every time a family member snuck into the room to take a peak, the word I heard was “calm.” Indeed, this color scheme is truly calming.
The surface of the wallpaper has a unique, dry feel to it – almost chalky. It gives it a blissful, matt finish.
The manufacturer is Anderson Prints, in their Eco Chic line, and was bought from Ted at the Shade & Drape Shop on Richmond & Kirby.
The Wallpaper Lady's Blog 