A Really Nice Faux Grasscloth , Suitable for Bathrooms

The homeowner wanted the look of grasscloth, but didn’t want the stains that can happen when splashed with water or toiletries.  Another displeasing feature of real grasscloth is the very visible seams , and the likelihood of color differences between panels (called paneling or shading ).  So she opted for this textured vinyl version.  She loves the look.  It is a handsome room!

Original 1990’s paper has been stripped off, Roman Pro 977 Ultra Prime wallpaper primer has been applied, and we’re now ready for paper!

This material has a pattern that matches from strip to strip, so you don’t get the eye-jarring look of broken fibers at the seams , like with real grasscloth or other natural materials. 

Here’s a close-up, detailing the texture.  About ¼ from the right is a seam – it’s barely noticeable . 

Opposite wall.  For balance, I plotted that the seams fall at the same point on each wall – 18” from the mirror frame

I’m getting ready to hang a strip that will knock against that mirror frame.  To keep paste from slopping onto the molding , I’ve applied this thin, flexible blue plastic tape along the edge.  This will keep paste off the molding while I trim that strip to fit against the molding.  Once that trimming is done, I’ll remove the blue tape and then smooth the wallpaper back into place.

Since this is a dark wallpaper, I worry about the light colored primer peeking out at the seams.  This can happen because sometimes the factory hasn’t trimmed the edges perfectly straight , or the wall may have uneven areas or bows , or some papers shrink a tad when they dry .  So here I’ve plotted where the seams will fall and have striped the area with diluted paint .

I use bottles of craft paint from the hobby store (good old Texas Art Supply !), and apply with a scrap of sponge .  And my trusty Gatorade bottle cap with water, to dip the sponge into to dilute the paint … you don’t want full strength paint under there.  Wallpaper wants to adhere to a primer made for wallpaper – not paint designed to color Christmas ornaments. 

Another and probably more important trick is to color the edges of the wallpaper.  This navy blue wallpaper was printed on a white stock / substrate , and it’s highly likely that the edges of that substrate will show at the seams .  So, again back to Texas Art Supply (or a good hobby store) for chalk or pastel , which I run lightly along the edge from the back so as not to get any color onto the surface of the wallpaper .  That little dark nub you see is my chalk… the stuff breaks easily.  It’s important that you not get oil pastels or use any kind of ink marker, as these will leech into the wallpaper and stain it, leaving you with a nasty dark line down the seam . 

I really liked this product.  It was flexible enough to wrap around a rounded / bull-nosed corner , but stiff enough to not warp .  It’s on a non-woven substrate , which contains polyester , which makes it less likely to shrink .  This stuff is also designed to strip off the wall easily and in one piece with no damage to your wall when you redecorate .  Another advantage of non-wovens is that they can be pasted and hung immediately, with no booking or wait time.  Although I generally prefer to paste the paper , you also have the option to paste the wall with this material.
The non-woven backing won’t be sucking up humidity like the paper backings used years ago (or in modern lower-end products), so greatly reduced chance of seams coming loose if your teenager spends an hour steaming up the bathroom . 
The vinyl surface means that it will be resistant to stains from water , toothpaste , and little (and big!) hands . 
In addition, I liked that the material has a realistic grasscloth look, and a realistic texture , as well as a pattern that could be matched, which helps disguise the seams.  I didn’t match the pattern in the corners, though, to avoid having the horizontal bands running around every wall of the room at the same height.  Looks better to break it up a bit.  Also gave me more flexibility in placement of seams.   
The brand is A Street Prints and is in their Scott Living line  (as in the Scott Brothers of HGTV fame). 
The home is in the Champions Forest area of Houston .   
installer paperhanger

Geometric on Tricky Outside Corner

OK, never mind the ’80’s-era toilet paper holder that’s recessed into the wall here and is not removable – which presents a challenge all its own. My issue is adding the next strip of wallpaper to the left, turning the corner, and keeping the pattern matched as well as possible in both the inside corner and around the outside corner.
Usually, when turning inside corners, you wrap the paper around the corner 1/8 of an inch, and then cut a new strip of paper, match the pattern, and then overlap it that 1/8″ . That helps eliminate issues like mis-matches or wrinkles due to crooked corners or uneven / bowed / out-of-plumb walls . (no walls are ever perfect )
But in this case, we also have an outside corner to wrap. Even though it’s only about 2″ wide, that edge can cause the pattern to go off-plumb , or to create wrinkles in the wallpaper .
Going against most rules of wallpapering , I’ve decided to wrap the next strip around this 2″ wide wall and then onto the wider wall to the left .

Here I am, starting to position that next strip. I’m not going to try to wrap a full 27″ wide strip around this turn. Instead, I’ve trimmed it vertically along a horizontal stripe , which makes this strip narrower and more easy to handle , and also will help in placement of the next strip.

Now I’m pushing it into place into that corner. Note how the paper is wrinkling, both on the wide wall, and as it comes around the 2″ wall.

Another shot of the placement and wrinkles .

Using my plastic squeegee smoother to press the paper tightly into the inside corner. Note that, since the corner isn’t perfectly straight or plumb, there were a few areas where I couldn’t press the paper tightly into the wall, but had to leave a bit of a gap or air bubble, in order for the left edge to wrap around the turn.
The plastic smoother can also be used to gently push out wrinkles on the larger body of the strip of paper to the right. Don’t press too hard , nor overwork , because you don’t want to stretch the paper – that will cause more wrinkles.

The plastic smoother took care of the inside corner. Here I’m using my damp microfiber cloth to tightly press the paper around this outside corner .

OK. Paper’s wrapped tightly around this corner – but, because the corner isn’t straight , we’ve got wrinkles and warps .

Sometimes, you need to take a scissors to make relief cuts to help ease the paper around the corner . Try to make your cuts along an element of the design , to make the slit less noticeable.

here is that little narrow bit, finally wrapped around the outside corner. Now we need to add the next strip to the left of this. Note that this narrow strip isn’t straight nor plumb nor equidistant from the corner that we just turned. Nor is it equidistant from the next corner we have to deal with, which is to the left (not pictured).
Since we want the wallpaper strips to match in the corners, it’s important that the wallpaper pattern fall in the corner to the left at the same point from ceiling to floor. Complicated to explain.

So I’m taking a fresh strip of wallpaper , made sure the pattern matches correctly , and have trimmed it vertically along the tan stripe . Now placing it along this wrapped edge.
Because I’m overlapping instead of butting , I’m able to pull the new strip to the right or left, to keep it equidistant from the right outside corner . Or, from the inside corner to the left.
Actually, I don’t care much about the right side. The eye won’t notice if the new strip isn’t perfectly plumb . Nor will it notice if the pattern match isn’t 100% perfect . But it will notice if the pattern doesn’t match perfectly in the inside corner to the left.
So I’m pulling and manipulating and overlapping the strip a bit, so that the left edge of it is exactly 10-3/4″ from the left edge. This ensures that the pattern motifs fall all at the same point into that corner on the left.
Do I can cut my next strip, trim it vertically so the design matches with that in the corner, and get a perfect pattern match in the corner. Kinda difficult to explain, but I hope you can follow what I’m describing.

Note that this overlap is causing a bit of a ridge under the paper . Hard to see here, but when the paper dries and shrinks tight against the wall, it will be a little more obvious. But I’d rather have a ridge on the right, than a pattern mis-match in the corner to the left.
Oh, and never mind that little pattern mis-match to the right … that’s the paper wrapped around the corner, so you’re looking at different dimensions, not a pattern mis-match.

Here is that strip finished. The vertical strips isn’t perfectly plumb, but no one can tell that.
ut the pattern is perfectly straight in the inside corner to the left . So when I take my subsequent strip and trim it vertically to remove the right edge by approximately 10-3/4″ , the pattern should match perfectly in this inside corner. (It did!)

This “sort of” Greek key trellis geometric design is by Thibaut , one of my favorite brands. It was on a triditional paper substrate , and was hung via the paste the paper method .
It was purchased from my favortite source for wallpaper in Houston , Dorota Hartwig at the Sherwin-Williams in the Rice Village , who has more selection books than anywhere else in the city – and knows what’s in every one of them! Call before heading over (713) 529-6515 .
The home is in the Champions Forest area of northwest Houston.

Wallpaper Repair – Always Save Your Leftovers

Here is damage to a wall behind a mirror in the powder room of a home in the Champions Forest neighborhood of northwest Houston.

Explaining this repair in detail would be pretty difficult, mostly due to how the original installer fiddled with the pattern to make it fit an odd space, and to what I had to do to work around that.

But the most important thing is that the homeowner saved all the wallpaper left over from the original installation back in the ’90’s, so I had what I needed to do this repair.

If you look closely, you might see some pattern mis-matches. But these are minimal because of some tricks I played, and because the pattern was forgiving. The mirror will cover everything, so any irregularities will be hidden.

But the bottom 3″ or so running along the backsplash and visible under the mirror are intact, so will look good when the mirror is replaced. This wall will also look good if a different mirror is used in the future.

Repairing Damage from Hurricane Harvey

This home in the Champions Forest area of north Houston received flood damage after Hurricane Harvey. The bottom 2′ or so of drywall had been cut out and replaced by the restoration contractor. The only thing is, the new drywall was recessed back about 3/8″ from the existing drywall. Even though this was near the floor in the niche behind the refrigerator, the homeowner didn’t want to have a difference in wall height, nor a mis-match in the wallpaper pattern.

So I used joint compound (“mud”) and drywall seam tape to bridge the gap and to float out the discrepancy. It took three coats, and several sandings, plus a sealing primer, but the finished wall is pretty even and smooth. (2nd photo)

There wasn’t enough left over paper to replace the whole alcove, so I used scraps to piece in the bottom area. Rather than make a straight horizontal cut 2′ above the floor, it’s less eye-catching to have the patched areas run along a feature of the design, such as the vines and branches in this pattern. (3rd photo)

Once the new strips were smoothed into place (4th and 5th photos), the patched areas are virtually undetectable.

Sometimes people complain about having left over wallpaper. But here’s a good example of why you should. (last photo) This homeowner had kept all her leftovers in their original wrappings and in their original box, in a climate-controlled environment (not the garage or attic), and she had what was needed to make this repair (and several others around the room that are not shown here).