This young couple hosts the mother / mother-in-law a few times a year, and are lucky enough to have a private spare bedroom for her. To make it special, they wanted to jazz up the area a little. Enter this fun and whimsical wallpaper pattern .The room before was a pretty shade of murky teal – but needed personality and warmth. The wall started out with a light orange peel texture . I skim-floated the wall, and then sanded it smooth . Along the baseboard at the floor , here’s the dust from sanding , along with the sanding sponge I use – this is a modern take on the idea of wrapping sandpaper around a block of wood . I tack painter’s plastic across the wall from ceiling to floor to prevent dust from getting into the room or onto the furniture . Here’s the wall smooth and primed , ready for wallpaper . Since this is a dark wallpaper and I want to be sure that the white wall does not peek out from behind the seams, I stripe dark paint along the wall under where the seams will fall. Because non-woven papers don’t expand when wet with paste , it’s simple to measure the width of your strips and plot out where each seam will fall. Use the laser level as your guide . Do a Search here (upper right hand corner) to read more about this technique. I use craft paint from Texas Art Supply (or any hobby store ), diluted with water from a Gatorade bottle cap , and applied with a scrap of sponge . Further insurance is taking a chalk pastel (never oil pastel – oil bleeds and will stain wallpaper) and running it along the edge of the wallpaper strip – from the backside to avoid staining the surface – to cover the white substrate the wallpaper is printed on. This is to prevent white from peeking out at the seams , which can happen with dark papers. Centering the first strip in the middle of the wall, and using my laser level to ensure the strip is nice and straight and plumb . Note: The strip is not centered on the wall. The dominant pattern element is. Notice that the center of the dominant pattern motif – the white circular flower – is 3.5″ to the right of the left edge. This means that I had to position the left edge of the wallpaper 3.5″ to the left of the center of the wall, in order to get the round white flower to fall down the center of the wall. When you look again at the finished photo, you’ll notice that the white flower falls down the middle of the walls, and that it also appears at equal distance from both the right and left walls. Most people wouldn’t be able to put their finger on this symmetry , but it is something they subconsciously notice , and it lends a feeling of orderliness to the room. As orderly as you can be, that is, with pigs dancing around the meadow dandelions ! Finished accent wall . The three other walls painted in blue were a bit of a surprise, because one would think the more dominant color of green would be used. But with so much green in the wallpaper, green on the walls, too, would have been too much, perhaps. I like the cool feeling that the blue creates . There is plenty of the exact same blue in the wallpaper pattern to tie the walls and wallpaper together. Close up shows the stamped printing technique . You’ve gotta love a frolicking pig in a hand-knitted sweater! This pattern is called Hoppet Folk and is in the Wonderland line by Borastapeter , a Scandinavian company . It’s a nice, sturdy but flexible non-woven material that can be hung via the paste the wall installation method . In addition, this product will strip off the wall easily and in one piece , with no damage to your walls, when it’s time to redecorate. This is a very popular pattern, and I’ve hung it more times than I can count, just in the last two or three years. It does come in other colors – but most people gravitate toward this black version. The townhome is in the Rice Military area of central Houston .
Grasscloth is a natural material that cannot be matched from strip to strip, so all the seams will be visible . In addition, there is usually a slight but noticeable color difference between strips / panels (called shading or paneling ) . So it’s important to plot the layout of the strips to give the most visually pleasing overall look. Usually this means balancing the width of strips so they are all equal , at least on the same wall . We call this engineering . This wall presented particular challenges , due to the widths of the elements. Grasscloth comes 36″ wide . You can use your straightedge and a sharp razor blade and trim it down to any width you want. The width of both the large wall spaces to the right and left of the bank of windows was 34.” The width of each window was about 35.” The width of the two spaces in between the windows was 7.” So you’d think I could trim my panels on either side of the windows, and then over the windows, to about 34″-36″ – give or take a few inches (or fractions thereof). But that would leave me with two 7″ wide strips between these 35″ panels. Although the look would be uniform and mirror-image from the center outward, moving from right to left you’d have: 35,” 35″, 7,” 35,” 7,” 35,” 35,” … those 7″ breaks were just not going to look right. One option was to determine the width of the wall (189″) and make each strip an equal width. This worked out to six strips, each at 31.5″ Not good, because this would mean a seam down either far side. And since those sides were 34″ wide, that would mean a 31.5″ wide strip and a strip 2.5″ wide. Not attractive at all, and it would use up an extra strip of wallpaper. This six strips @ 31.5″ wide scenario might also land with a seam smack in the middle of those 7″ wide interludes in between the windows. Not attractive at all. So I decided to make the two outer strips 35″ wide. That left 119″ of wall space above the windows to be covered with wallpaper. Do some math and you get four panels of 29.75″ wide. This gave a balanced and uniform look to the area over the windows, and also prevented seams from landing between the windows. Moving right to left, I cut and hung the full length outer strip first. Then I cut and hung the strip over the window on the right. Then I measured to find the centerpoint of the window in the middle. Turns out it was a bit less than 29.75″ away. So I trimmed that next over-window strip accordingly. Once that was in place, I measured from that center point above the middle window out to where my left full-height panel would fall, 35″ out from the wall. Took the resulting measurement and divided by 2. Lo and behold, each of the next two panels over the window was going to be a bit wider than 30.” No problem. No one (but a paperhanger or maybe an engineer) is going to notice a 1/4″ or even a full 1″ difference in widths between this strips over the windows. Another thing to point out … it’s important that I took measurements before cutting these strips for this second left-hand section. Because, since grasscloth comes at 36″ (and walls can be wonky), if my strips had been narrower (say, 28″), that last full-height panel on the left might have ended up needing to be 37″ wide – and that wouldn’t work because it only comes 36″ wide – plus you need at least 1/8″ to wrap around the corner. Luckily I had the flexibility to be able to trim the panels over the windows to any width needed, to accommodate all this. If you’ve followed all this so far, let me also toss in that we also need to figure how to get paper in between those windows. More on that below. In this scenario, I’m moving from right to left. Area beneath the windows needs to be treated in the same way, and preferably with widths that match what’s going on above the windows. In addition, it’s tricky because after you move across 12′ of wall space, the strips above and below the windows are going to twist and torque out of shape, so that last full-length panel on the far left might not butt up perfectly with the last strip under the windows. The grasscloth is black , and my wallpaper primer is white . It’s common for teeny gaps to appear at the seams . In this case, it’s likely that white wall would peek out from those gaps. So I like to stripe under where the seams will fall with dark (diluted) paint . This takes measuring , plotting , and also a heat gun to get the paint to dry before the wallpaper hits it, to avoid staining. You can do a Search here to read more about this technique . Now let’s talk about getting wallpaper in between those windows. As you can see in the photo, if I hang a 30″ wide strip, a whole lot of paper is going to be cut off and thrown away. Also, a whole lot of sticky, pasted paper is going to bump against that window molding and maybe even the window glass. A lot to clean up! And unwieldy, to boot. My solution was to stop the wallpaper just a little below the tops of the windows. Then I would patch in a 7″ wide strip in between the windows. This is trickier than it sounds, because, if it were a paper wallpaper, I could simply cut along a design motif and overlay the 7″ wide piece. But grasscloth is thick and overlaps don’t look good. Also grass has no design elements , and the reeds of grass don’t necessarily fall perfectly horizontal , and even if you cut everything perfectly true to square , if the window molding is a teeny bit off-plumb , then your edges won’t butt up perfectly. So that’s a good reason for striping the black paint under where the butt join will occur. Same thing for the sections under the windows. I measured and positioned the strips so that the top edge (which I had trimmed to be perfectly horizontal) fell between the narrowest part of the windowsill molding, for less visibility. I admit, instead of butting the two pieces, here I did overlap the 7″ wide strip about 1/4″ onto the piece under the window, right at that narrow junction. It’s only about 3″ wide, and I figured no one is going to be examining it that closely, anyway. This saved me about a half an hour of measuring, trimming, testing, repeat, repeat. This is my second window interlude, and by this time I had realized that it’s hard to trim stiff grasscloth around intricate moldings precisely . So I used paint to fill in the edges around the window molding, just in case there might be any gaps between the grasscloth and the molding, so you would see black instead of the white molding paint. I did this with a small sponge; if I had used an artist’s brush it would have been a bit neater and tighter to the conforms of the molding. But sometimes you’ve gotta relax and realize that no one’s going to be scrutinizing the insides of moldings below shin-level. Area over windows finished, with drapes back in place. Turns out this particular grasscloth is so uniform in color (quite unusual, I will add), that you can’t really see the panels , nor their equal widths , anyway. I’m still glad I took the time to do all this math and trimming. Area below the windows, done. That last seam on the left bears some explanation, too. Moving across the top of the windows, I measured that that last strip – the full-length strip – would need to be exactly 35″ wide. It butted up nicely to the last strip above the windows. But, due to twisting , shifting , expansion , unlevel and unplumb walls and ceilings , and other factors, there is a really good chance that that last 35″ wide strip would not butt up perfectly with the last 30″ wide strip under the window . So I planned to splice these last two strips together. Yeah, the drapes are hanging there, I coulda overlapped the two strips about 1/2″ and the drapes would have covered it. With a thin wallpaper, I probably would have done this. But grasscloth is thick, and an overlap would be visible , and also the adhesive / paste can’t be trusted to adhere as well to grass as it would to paper . So I plotted for a splice. Instead of trimming my last strip under the window to 30″ (read above), I trimmed it to 32″ wide. That way, when I hung the last full-length strip to the left, which was 35″ wide, it overlapped the piece under the window by a few inches. Then I did a double cut and spliced the two pieces. See below for details about that technique. Grasscloth is 36″ wide, and this wall area is wider than that. So two strips were needed. This means you’re going to have a seam, and since grasscloth seams are always visible, it looks best to plot to have the seam fall down the center. It uses more wallpaper to do this, but it looks much better than having, for example, a 36″ wide strip next to an 8″ wide strip. As mentioned above, in case you get thin gaps at the seams, a dark stripe of diluted craft paint under where the seam will fall, will prevent white wall from showing through. Rounded / bull-nosed edges and corners have been popular in new construction for at least 10 years. I wish they’d go away. They’re very difficult to trim around, and hard for the paper to conform to and adhere to. It’s very hard to trim around that rounded edge, because the paper is hanging over and blocking your view, because grasscloth is thick and stiff and your fingers can’t feel through it, and because the edges aren’t necessarily true and plumb so a laser level or other level won’t help you much. I use this little gadget as a trim guide. It’s actually a small section of the same corner bead material that drywallers use when they assemble these walls. Cut to about 1″ long and notched in different places where you might trim along the edge of the wall. It’s intended that you place your trimming knife in one of the notches and slide the gizmo along the edge and make your cut. I find that awkward and also inaccurate. So I prefer to use the notches as a guide and mark where I plan to trim with a pencil. Since this wallpaper is black, I used this marking pencil from my home sewing kit instead. Chalk might work, but I was afraid it might now wipe off completely. The pink pencil line was barely visible, but it was enough for me to use a scissors to trim along the grasscloth. I like this better than using a razor blade as I can see better, and also less chance of scoring into the primer or wall. Which raises its own set of issues – do a search here to find previous posts.Inside view of the trim guide. Finished arch. Note the four panels of equal width above the arch. And two flanking full-height panels also the same widths. I was lucky that there was no pattern to match, so I was able to butt my two flanking strips right up to the edge of the bull-nosed corner. No trimming needed! Then I measured the remaining width between these two strips (the area over the arch), divided by four, and cut four strips of equal widths. I hung the two on the left, and then one on the far right. This left one strip still to be positioned to the right of center. So the pieces are going to meet over the arch, rather than the last strip falling in a corner. Same as the last strip under the window (discussed above), it’s really difficult to get your last piece to fit in here perfectly. I’ve done it, but it takes a lot of measuring, trimming, testing, retrimming, and often starting all over again. So I did a double-cut / splice. A double cut involves cutting each strip an inch or so wider than it should be, and overlapping the two. Then you take a straight edge and sharp razor blade and cut through both layers. This handy tool is a wonderful non-slip guide for this process. It was invented by an installer colleague in the Wallcovering Installers Association ( WIA ) and she has them fabricated in various lengths (along with other cool tools ) and sells them on-line. Contact me if you’re interested. Anyway, it takes a lot of strength to cut through two layers of grasscloth, so somewhat difficult for lil’ ol’ me. You also want to be sure to not cut / score into the wall, because the tension of drying wallpaper can tug at the wall and cause it to actually come apart, leaving an open seam that’s difficult to repair. So you’ve got to put some padding under the wall where the cut will take place. I use special strips of polystyrene (hard but flexible plastic) to pad the wall. Also invented by a colleague in the WIA , who also sells other cool tools and supplies. Contact me if you’re interested. This black grasscloth was printed on a white substrate. If the seams aren’t absolutely tight, there can be worries about the backing showing through to the front. So sometimes we’ll take a piece of chalk or pastel (never oil pastel or permanent markers because they bleed and stain ) and run it along the edge of the paper – from the back, and taking care to not get chalk on the surface. I do this frequently with dark papers ( do a search here to see previous posts ) but opted not to do it with this grasscloth. It wasn’t necessary, and might have stained the porous reeds of the grass. It was beneficial, though, to have striped dark paint on the wall under the seams, as mentioned above. Ugh. Grasscloth comes 36″ wide, and this section of wall is 38″ wide. It’s not visually pleasing, nor is it easy from an installation point of view, to have a 36″ wide strip next to a 2″ wide strip. Or to use scraps and put a 25″ wide strip next to a 13″ wide strip. So best to plan two strips of equal widths. Two strips, each 19″ wide, with the seam down the middle. Actually, the strip on the left was 19″ wide, but I trimmed the strip on the right to 21″, because I like the wallpaper to extend 2″ over the top of the door molding. This provides a more stable surface in case of shifting foundation or walls, and less likelihood (knock on wood) of the seam opening up should the house / drywall experience shifting. Note that design “rules” caution against seams down the middle of spaces. But it would have been more visually distracting (and used up more paper) to have made three strips of each 12.75″ wide. And would have looked even dumber to have used scraps left from other walls and put together two strips of disparate widths. So the homeowner and I discussed during our initial consultation , and she was happy with the center seam. Once it was all finished, this particular grasscloth was so even in tone that you barely see the seams, anyway. Win-win! This did use up additional paper, though, as noted in a previous photo above.
Vanity wall was originally textured and painted with a semi-gloss . Here it’s been skim-floated , sanded , and primed – ready for wallpaper. Finished. There’s a cool light-up mirror that will hang on the brackets under the light fixture .Opposite corner before.Finished. This room wouldn’t have half the impact without the black moldings and ceiling. The homeowner said she envisioned a jewel box – all tufted and lined with velvet . Well, I’d say she nailed the look! As the dark and mysterious wallpaper moved from left to right, the room began to take on a mood . I love the juxtaposition between a clad wall and a bare wall. Close-up.Detail.The husband is handy, and I really appreciate that he removed the vanity and sink . This made it a lot faster and easier for me, and ensured better adhesion of the wallpaper around the plumbing pipes . And also eliminated stress and creases on the paper that can happen when bending and folding to work it around obstacles. Here is the modern looking vanity that will go into the powder room . To keep white primer from showing at the seams , I striped black paint on the wall under where each seam would fall. Do a Search here to read previous posts about this technique.I use matt finish craft paint from the hobby store , a scrap of sponge , and a bottle cap full of water . Do a Search here to read previous posts about the process and materials . I also run chalk along the edges of the wallpaper, to cover up the white substrate , to ensure there will be no white peeking out at the seams . Again, do a Search on key words to learn more about this technique . Dang it! I forgot to take a picture of the label! But this wallpaper is by York and is called On The Prowl . It’s vinyl on a non-woven backing . The instructions said you could paste the wall for installation . But I pasted the paper, and I think with this product it’s better, because it did seem to want to expand a bit. If you paste the wall and then the paper stretches, you’ll end up with buckles at the seams or bubbles within the strips . The material was fairly flexible , which was nice because it allowed me to “mush” the paper to conform to some pretty un-plumb walls. Although York is one of my favorite brands , I wasn’t real crazy about this particular wallpaper. Still, it seamed up nicely, didn’t shrink, has a vinyl surface that will resist splashes and fingerprints , and is designed to strip off the wall easily and in one piece when it’s time to redecorate . This is a townhome in the Rice Military area of central Houston .
When wallpaper gets wet with paste, it expands a bit. And when it dries, it can shrink just a tad. That teeny gap at the seams can expose the wall underneath it. This can happen even with the non-woven materials, which are supposed to be dimensionally stable. In addition, manufacturers usually print on a white substrate, so sometimes you see the edges of the paper at the seams, too. All this is much more noticeable on a dark paper, such as here. One thing I do to prevent / minimize this is to strip the wall with dark paint under where the seams will fall. So even if a seam opens up a bit, you’ll see dark, not white. Since non-woven wallpapers don’t expand (much), it’s easy to measure the width of your strips and plot where the seams will fall, use a level, and then apply the paint. I use plain old craft paint from the hobby store. I use a scrap of sponge and dip that in water (in my orange bottle cap) then into the paint, and then run my stripe down the plumb line I’ve drawn on the wall or used my laser level to shoot a vertical line. It’s important to not get the paint too heavy or thick, because the wallpaper paste may not want to grab ahold of paint like it wants to hold on to a wallpaper primer. And definitely don’t use a gloss paint. Be sure that it’s good and dry before you hang the wallpaper. A heat gun will speed things along if needed.Not pictured, but you can look up other posts here … I also take a bit of chalk of a corresponding color and run it along the edge of the wallpaper to cover up that white edge. It’s important to apply the chalk from the back, to avoid getting any on the front of the wallpaper. Some colleagues use water markers, pencils, or gouache paint. Whatever you use, do not use anything with oil-based inks or colors. These will bleed and stain your wallpaper. Chalking the edges is more important than striping the wall, IMO.This pattern is called Allure and is by Graham & Brown , a brand I like a lot.
Dark papers are popular right now. But since wallpaper shrinks a tad when it dries, and since it’s usually printed on a white substrate, it’s possible that hairs’-breadth gaps of white wall may show at the seams. One way to prevent that is to stripe the wall under where the seams will fall with a color similar to the background of the wallpaper. Be careful to not get it too dark, as too much pigment may interfere with the wallpaper primer’s ability to perform optimally. I measured the width of the strips, and then used a laser level to guide my stripes. I use craft paint from the hobby store, and daub it on with a scrap of sponge (right) and dip into a bit of water, which I keep in a Gatorade bottlecap (left). To get rid of the white edges of the substrate, I use a bit of chalk (some folks use paint – but make sure it’s water-based …. NEVER use oil-based paint, markers, or chalks, as they will bleed onto the surface of the wallpaper). I run the chalk along the edge of the wallpaper strip, making sure to work from the back side, to prevent the chalk from working its way onto the surface of the wallpaper. Use a light touch, but cover all of the white edge. Finished wall. Don’t see no stinkin’ white gaps! 🙂 The mural pictured is by RebelWalls.com
Walls smoothed and primed, ready for wallpaperFlowers, birds and – COLOR!Reminds me of this Pierre Frey which I hung in a nursery a few weeks ago.
Home office, craft room, veg-out room – whatever the “official” description, this room in the front of the house belongs to the lady of the house. She loves birds and flowers and bright colors, and was thrilled to find this wonderful wallpaper pattern on Anthropologie.
Most of Anthropologie’s papers are by York, in their SureStrip line, which is one of my favorites. The material is pre-pasted. I like to sprinkle water on the back and then spread it around uniformly with a paint roller, and then book for a few minutes in a plastic trash bag.
The paper goes up beautifully and the seams are invisible. SureStrip is designed to pull off the wall easily and in one piece when it’s time to redecorate.
This neutral-hued grasscloth sure warms up the look of these display shelves, adding both soft color and texture. The homeowner’s books and decorative items stand out much better.
None of the shelves was removable, so I had to cut and install TWENTY FIVE separate pieces of grasscloth wallpaper for the backs of these bookshelves.
To minimize trimming inside those small, tight cubicles, I took careful measurements and then pre-cut my pieces. I used a straight edge, razor blade, and one of those “self-healing” cutting mats that are used for sewing and crafts. The mat was marked both vertically and horizontally in inches (and graduations) and had easy to see right angles.
I cut all my pieces a mere 1/2″ larger than the dimensions of each cubicle. I used the craft mat and straight edge to cut a right angle in the upper left corner of each piece of grasscloth. I could position this in the upper left corner of each cubicle, which also butted it up perfectly against the top and left sides of the cubicle.
Then all I had to do was use my razor knife to trim the grasscloth on the right and bottom sides, to fit into the cubicle.
I spent a full four hours priming, then measuring and labeling each cubicle, and then cutting and pre-trimming each of the 25 pieces of grasscloth. Look at the photo of my measurements!
All this effort paid off, because every single piece of material went into its cubbyhole perfectly, and required trimming on just two sides (instead of four). The install still took a full eight hours. But it was fun and challenging, and a different work-out for the brain from hanging paper on tall, flat walls.
This grasscloth wallpaper is by Thibaut. I forgot to take a photo of the label, but it was a really nice paper, and, even though I had only one seam (in the TV niche), for once there was no issue with shading or color differences – in fact, that one seam is all but invisible. I hung this in a living room in a townhouse in the Rice Military / Camp Logan neighborhood of Houston.
The Wallpaper Lady's Blog 