Smoothing Over A Mess

This kind homeowner had the sink / vanity in this powder room removed. This makes it a LOT easier and faster for me to to get the wallpaper up, and with less stress on the paper and fewer relief cuts .

Removing a sink that’s attached to the wall often damages the surface. Here you can see how the workman used spackle compound to cover the torn drywall and other damage.

s

Close-up. This isn’t a very smooth surface, and the wallpaper will have a hard time grabbing ahold and adhering. It’s also way too porous and crumbly to support wallpaper.
In the top photo, you see where I have applied smoothing compound on the upper portion of the wall. I’m working my way down.
Once it’s dry, I will sand and prime it, and it will be nice and smooth.

Here’s a shot of the fresh smoothing compound, before sanding.

Some people use a drywall taping knife or a broad knife to apply the plaster-like substance. I prefer the trowel you see in the photo, because it gives me more control and precision.
The 2″ flexible putty knife is for getting into smaller areas. The 3″ stiff ” Hyde ” putty knife is for knocking off high points or bumps on the wall before applying the smoothing compound.
This process is called skim-floating or skim-coating .

I like to use the Plus 3 lightweight joint compound made by Sheetrock . We just refer to it as mud . Find it in the drywall aisle.
The Plus 3 spreads on easily enough, sands easily , and the dust falls to the floor where it can be vacuumed up easily – as opposed to getting air-borne and drifting all over the place.
This box, which is approximately one cubic foot , weights 32 pounds . Ugh. Try carrying that across a parking lot and then up to the third floor of a townhome!

I like to transfer the material to a 5-gallon bucket. This is what it looks like in the bottom of the bucket.
Easy to scoop out. When I’m finished, I use a wet hand to smooth down the surface, wipe residue off the sides of the bucket, then place a thick sheet of plastic over the surface to keep air from drying it out. Then, of course, I put the lid onto the bucket.

Danger Signs of an Unstable Wall Surface

These nails were holding picture hooks to the wall. The hooks had an adhesive backing. When they were removed from the wall, chunks of latex paint stuck to them and pulled away from the wall, revealing a crumbly sub-surface. This is bad news for wallpaper that might be hung on top of this.

Other spots. What happens is, this is a 90 year old house. Over the years, many coats of paint and other surface treatments have been applied to the walls of this dining room. These coatings are not necessarily compatible with each other. Plus they may have been applied without the proper surface preparation. Oil based paint, then latex, then someone rolls on a gloss paint, the next guy follows with latex but neglects to de-gloss the previous layer so the new layer doesn’t really stick well.

Somewhere along the line, something got chalky. Here you see I have wiped crumbly chalky substance from inside the wall. This is why the latex paint is not adhering well and pulled away so easily. Nothing sticks to dust or grit or chalk.

Gardz is cool stuff. It’s a penetrating sealer that soaks in and actually binds crumbly materials together, drying into a hard, solid mass. The problem here is, it won’t penetrate the paint that is on top of the unstable layer, so we’re still dealing with a wall that has potential to come apart (delaminate).

Gardz applied. You can see how it has soaked into the porous areas, but is sitting on top of the latex paint.

The problem with an unstable wall and wallpaper, is that, as wallpaper sits on a wall and the paste dries, the paper shrinks just a tad, and this shrinking puts tension / torque on the wall beneath it. Sometimes this is actually powerful enough to pull the layers inside the wall apart, resulting in seams that split open.

These are not “loose seams,” but the paper actually taking layers of paint and dust along with it. Really can’t be repaired.

So best to find a way to prevent it from happening in the first place. More on that later.