Using One Strip to Cover Two Areas Saves Wallpaper

This wallpaper is 20″ wide . My next strip to the left needs to be 20″ wide above the window – but only 1.5″ wide down the side of the window. I hate to use a whole 6′ long strip for this area. Because, as you can see, most of the strip will be where the window is, and will be cut off and thrown away.

But here’s a plan. The same thing is happening on the right side of the wall, on the window to the right. About 10″ of the wallpaper has extended over the window, leaving about 10″ of the lower portion to be cut off and thrown into the trash.
NNo! Since I need a 1.5″ width of a right edge to finish my area on the left side of the wall (see previous photo), I can use this discarded lower 10″ of wallpaper to cover that 1.5″ to the left.

Planning ahead and measuring carefully, I removed the lower section of wallpaper that would have been hanging over the window / shutters . I left plenty of overlap to allow for trimming along the top and along side the window molding. Added bonus – because I’m now not wrestling a 20″ wide strip of paper next to this window and shutters, it keeps a lot of paste from slopping onto the window molding and shutters .
zin this photo, you see the 10″ wide strip I’ve removed. And also the 1.5″ wide strip from the left right edge, that will be put against the strip to the left.

Here’s my 1.5″ wide strip.

And here’s where I’m going to put it. Note that I cut a short strip to fit over the window . It’s 20″ wide – the width of the roll of wallpaper . I cut it long enough to come down the side of the window to where there’s a design element – in this case, a horizontal branch – to disguise the juncture of these two pieces of wallpaper .

About to go into place .

Positioned. Note the overlap of the branch, trimmed along the lines of the motif. This makes the overlap way less noticeable than a straight horizontal patch, or even a splice.
Note: I don’t like to splice / double cut in situations like these – cuts into the wall surface below and can cause the paper to come away from the wall. I don’t mind overlaps in these situations. They’re up high where no one can see, and also much stronger and more stable than a butted edge .

Teimming off excess along the window molding / trim .

Doone!

The tree and leaf pattern is called Twining and is by Graham and Brown . Like most of their materials, it’s a non-woven material and can be installed by pasting the wall – although I usually paste the paper . It is designed to strip off the wall easily and in one piece when it’s time to redecorate . The seams are invisible .

Geometric on Tricky Outside Corner

OK, never mind the ’80’s-era toilet paper holder that’s recessed into the wall here and is not removable – which presents a challenge all its own. My issue is adding the next strip of wallpaper to the left, turning the corner, and keeping the pattern matched as well as possible in both the inside corner and around the outside corner.
Usually, when turning inside corners, you wrap the paper around the corner 1/8 of an inch, and then cut a new strip of paper, match the pattern, and then overlap it that 1/8″ . That helps eliminate issues like mis-matches or wrinkles due to crooked corners or uneven / bowed / out-of-plumb walls . (no walls are ever perfect )
But in this case, we also have an outside corner to wrap. Even though it’s only about 2″ wide, that edge can cause the pattern to go off-plumb , or to create wrinkles in the wallpaper .
Going against most rules of wallpapering , I’ve decided to wrap the next strip around this 2″ wide wall and then onto the wider wall to the left .

Here I am, starting to position that next strip. I’m not going to try to wrap a full 27″ wide strip around this turn. Instead, I’ve trimmed it vertically along a horizontal stripe , which makes this strip narrower and more easy to handle , and also will help in placement of the next strip.

Now I’m pushing it into place into that corner. Note how the paper is wrinkling, both on the wide wall, and as it comes around the 2″ wall.

Another shot of the placement and wrinkles .

Using my plastic squeegee smoother to press the paper tightly into the inside corner. Note that, since the corner isn’t perfectly straight or plumb, there were a few areas where I couldn’t press the paper tightly into the wall, but had to leave a bit of a gap or air bubble, in order for the left edge to wrap around the turn.
The plastic smoother can also be used to gently push out wrinkles on the larger body of the strip of paper to the right. Don’t press too hard , nor overwork , because you don’t want to stretch the paper – that will cause more wrinkles.

The plastic smoother took care of the inside corner. Here I’m using my damp microfiber cloth to tightly press the paper around this outside corner .

OK. Paper’s wrapped tightly around this corner – but, because the corner isn’t straight , we’ve got wrinkles and warps .

Sometimes, you need to take a scissors to make relief cuts to help ease the paper around the corner . Try to make your cuts along an element of the design , to make the slit less noticeable.

here is that little narrow bit, finally wrapped around the outside corner. Now we need to add the next strip to the left of this. Note that this narrow strip isn’t straight nor plumb nor equidistant from the corner that we just turned. Nor is it equidistant from the next corner we have to deal with, which is to the left (not pictured).
Since we want the wallpaper strips to match in the corners, it’s important that the wallpaper pattern fall in the corner to the left at the same point from ceiling to floor. Complicated to explain.

So I’m taking a fresh strip of wallpaper , made sure the pattern matches correctly , and have trimmed it vertically along the tan stripe . Now placing it along this wrapped edge.
Because I’m overlapping instead of butting , I’m able to pull the new strip to the right or left, to keep it equidistant from the right outside corner . Or, from the inside corner to the left.
Actually, I don’t care much about the right side. The eye won’t notice if the new strip isn’t perfectly plumb . Nor will it notice if the pattern match isn’t 100% perfect . But it will notice if the pattern doesn’t match perfectly in the inside corner to the left.
So I’m pulling and manipulating and overlapping the strip a bit, so that the left edge of it is exactly 10-3/4″ from the left edge. This ensures that the pattern motifs fall all at the same point into that corner on the left.
Do I can cut my next strip, trim it vertically so the design matches with that in the corner, and get a perfect pattern match in the corner. Kinda difficult to explain, but I hope you can follow what I’m describing.

Note that this overlap is causing a bit of a ridge under the paper . Hard to see here, but when the paper dries and shrinks tight against the wall, it will be a little more obvious. But I’d rather have a ridge on the right, than a pattern mis-match in the corner to the left.
Oh, and never mind that little pattern mis-match to the right … that’s the paper wrapped around the corner, so you’re looking at different dimensions, not a pattern mis-match.

Here is that strip finished. The vertical strips isn’t perfectly plumb, but no one can tell that.
ut the pattern is perfectly straight in the inside corner to the left . So when I take my subsequent strip and trim it vertically to remove the right edge by approximately 10-3/4″ , the pattern should match perfectly in this inside corner. (It did!)

This “sort of” Greek key trellis geometric design is by Thibaut , one of my favorite brands. It was on a triditional paper substrate , and was hung via the paste the paper method .
It was purchased from my favortite source for wallpaper in Houston , Dorota Hartwig at the Sherwin-Williams in the Rice Village , who has more selection books than anywhere else in the city – and knows what’s in every one of them! Call before heading over (713) 529-6515 .
The home is in the Champions Forest area of northwest Houston.

Welcoming Room for Mother-in-Law

This young couple hosts the mother / mother-in-law a few times a year, and are lucky enough to have a private spare bedroom for her. To make it special, they wanted to jazz up the area a little. Enter this fun and whimsical wallpaper pattern .

The room before was a pretty shade of murky teal – but needed personality and warmth.

The wall started out with a light orange peel texture . I skim-floated the wall, and then sanded it smooth .

Along the baseboard at the floor , here’s the dust from sanding , along with the sanding sponge I use – this is a modern take on the idea of wrapping sandpaper around a block of wood .
I tack painter’s plastic across the wall from ceiling to floor to prevent dust from getting into the room or onto the furniture .

Here’s the wall smooth and primed , ready for wallpaper .

Since this is a dark wallpaper and I want to be sure that the white wall does not peek out from behind the seams, I stripe dark paint along the wall under where the seams will fall. Because non-woven papers don’t expand when wet with paste , it’s simple to measure the width of your strips and plot out where each seam will fall. Use the laser level as your guide . Do a Search here (upper right hand corner) to read more about this technique.

I use craft paint from Texas Art Supply (or any hobby store ), diluted with water from a Gatorade bottle cap , and applied with a scrap of sponge .
Further insurance is taking a chalk pastel (never oil pastel – oil bleeds and will stain wallpaper) and running it along the edge of the wallpaper strip – from the backside to avoid staining the surface – to cover the white substrate the wallpaper is printed on. This is to prevent white from peeking out at the seams , which can happen with dark papers.

Centering the first strip in the middle of the wall, and using my laser level to ensure the strip is nice and straight and plumb .
Note: The strip is not centered on the wall. The dominant pattern element is. Notice that the center of the dominant pattern motif – the white circular flower – is 3.5″ to the right of the left edge. This means that I had to position the left edge of the wallpaper 3.5″ to the left of the center of the wall, in order to get the round white flower to fall down the center of the wall.
When you look again at the finished photo, you’ll notice that the white flower falls down the middle of the walls, and that it also appears at equal distance from both the right and left walls.
Most people wouldn’t be able to put their finger on this symmetry , but it is something they subconsciously notice , and it lends a feeling of orderliness to the room.
As orderly as you can be, that is, with pigs dancing around the meadow dandelions !

Finished accent wall . The three other walls painted in blue were a bit of a surprise, because one would think the more dominant color of green would be used. But with so much green in the wallpaper, green on the walls, too, would have been too much, perhaps. I like the cool feeling that the blue creates .

There is plenty of the exact same blue in the wallpaper pattern to tie the walls and wallpaper together.

Close up shows the stamped printing technique .
You’ve gotta love a frolicking pig in a hand-knitted sweater!

This pattern is called Hoppet Folk and is in the Wonderland line by Borastapeter , a Scandinavian company .
It’s a nice, sturdy but flexible non-woven material that can be hung via the paste the wall installation method .
In addition, this product will strip off the wall easily and in one piece , with no damage to your walls, when it’s time to redecorate.
This is a very popular pattern, and I’ve hung it more times than I can count, just in the last two or three years. It does come in other colors – but most people gravitate toward this black version.
The townhome is in the Rice Military area of central Houston .