What’s A “Fat Cut” ?

Here, I’m hanging paper from right to left, and have just come around a corner , which is in the center of the picture. You almost never wrap wallpaper around an inside corner . Corners are never straight , and the paper will buckle in the corner . And the edge will not be straight , nor plumb , and thus the next strip won’t butt up perfectly against it . And it’s also probable that the strip will torque off either up or down, causing your pattern to creep up or down the ceiling and floor lines.
The answer is to stop the strip of wallpaper in the corner , and cut a new piece for the subsequent wall.
But you can’t just trim tightly to the corner. Because most likely there will be gaps (remember I said that corners are never straight?), so some of the wall will show.
So what you do is wrap the paper just a teeny amount around the corner , and then overlap your new piece over that. This does mean that you will lose some of the pattern in that overlap.
I can’t stand that pattern mis-match, so most of the time, the way I do it, I’ll take a fresh strip of wallpaper for the next strip (to be placed on the left in the photo) and trim it so the pattern matches as perfectly as possible. But I’m getting ahead of myself. Back to the fat cut …
In the photo, I’ve cut my strip on the left 1/2″ wider than needed to fit this wall. I don’t want this 1/2″ of wallpaper under my overlapped new strip, because the leaves a visible ridge. But you do want a little underlap, because you need that to prevent a gap from showing in the corner.
So in the photo, I’ve trimmed off most of that 1/2″ and trimmed it down to an unnoticeable 1/8″. How on earth can you get a trim that thin and that consistent?!

I use this handy metal plate with a rolled edge (on the left).

This plate has bends and other edges of other thicknesses , rounded edges , won’t leave marks on wallpaper, so it has many uses.

Here’s a close up of the trim guide edge that allows for that 1/8″ fat cut .

Back side of the plate. (Don’t mind the blue tape – it’s just there temporarily.)

This edge is a little thinner , and would cut too close for use in a corner. But it does have a use if you need a trim in an area where you don’t want the paper trimmed tightly into the edge / corner.

You’re looking at where wallpaper meets crown molding. This join edge has gaps between the molding and the wall in some areas, and other areas have gunk and uneven areas. Trimming with my usual trim guide would cut too close and let some of these icky things show. So here I’ve used the thicker trim guide. As you can see, it allows the wallpaper to wrap ever so teeny much of a bit, so it covers the bad area, but doesn’t creep onto the molding.

Here’s another example, along door molding. At the top, I used my usual thin trim guide (see below). But this allowed a bit of a gap to show, due to decades’ build up of paint , caulk , dirt , etc.
So, midway, I switched to using the steel plate as a trim guide. This made the cut just fat enough that the wallpaper wrapped a hair and covered the icky area.

Here’s my usual trim guide . I’m guessing it’s about 9″-12″ long .

You can see that the edge is very thin . In most cases, this is ideal, because it allows for good, tight trims right smack into corners and edges.
That steel plate shown above was invented by a colleague in the Wallcovering Installers Association ( WIA ) . They are all the same length, but they come with three different degrees of angles , and can be used for lots of wallpaper installation tasks .
The colleagues has them manufactured and then sells them to us paperhangers . She sells other cool tools , too. If you’re interested in purchasing any of these , or seeing what else she has, go here https://www.facebook.com/customwallpapertools or here https://www.wallpapertoolstore.com/?fbclid=IwAR2NFrG2gWSzNClNMB0gHDiQHbnkhyNhthaOFQaK8MCaU7rBYVQhYQkO0nc
Her name is Eunice , so we call them EuniTools .

“Smoke” On A Floating Wall

Digital Image

Digital Image

Digital Image

Digital Image

Digital Image

Digital Image

This wall in the dining room of a very contemporary new home in the Spring Branch area of Houston “floats” in the middle of the room. This breath of smoke floating across the wall adds a distinctly ethereal feel.

The interior designer on this job is Neal LeBouef, of L Design Group, who was expertly assisted by Anthony Stransky. I love working for these guys. And homeowners love their creations, which are crisp, sleek, modern, a bit edgy, yet still warm and comfortable.

The smoke mural was custom made to fit the wall, and came from Murals Your Way https://www.muralsyourway.com/ , a member of the Wallcovering Installers Association (WIA). Their murals can be printed on various materials, and I chose the vinyl on an Osnaburg backing.

Each of the three panels was about 42″ wide, and they were meant to be overlapped and then double-cut (spliced) at the seams. Great care was taken to not get paste on either the surface of the mural or on the ceiling, and to not score the wall while splicing.

I have a specially made 2 1/2″ wide plastic tape that keeps paste off surfaces, and another special 2″ wide polystyrene plastic strip that protects the wall from cuts from the razor blade, and a specially made non-slip straightedge used as a guide while trimming. All of these were invented and made by fellow members of the WIA (Steve Boggess and Eunice Bokstrom). Probably boring for the average blog-reader, but exciting stuff for us paperhangers. These things really helped make this job turn out perfect.