Picasso Slept Here – Crazy Pattern in a Complicated Powder Room

This is a fairly large powder room with a sloped ceiling, as it is situated under the stairs. You can see a bit of the ceiling at the top of the photo. The room also had this odd recessed niche with “columns” on either side, and a door leading to a closet.
In addition, there were tons of the rounded / bull-nosed edges that have been common in new homes in the last 10 years or so. These are tricky to wrap wallpaper around, and equally difficult to trim wallpaper to the edge.

Here is the niche area done, with wallpaper wrapped around the columns, and cut neatly along the horizontal bull nosed edge above the entry.
Wrapping the wallpaper around this edge and onto the ceiling of the niche would have made the area way too busy and claustrophobic. Because these edges are never perfectly straight and level, it’s also quite likely that the wallpaper will go crooked, and you’ll end up with gaps or overlaps at the seams.
A better option is to paint that ceiling area. I suggested the murky green color that’s in the leaves on the wallpaper pattern.

Here’s the east wall of the room. The vanity and sink are at the bottom right.

Here it is finished. In this case, the fir-down underside was only about a foot deep, so less chance of the wallpaper going crooked, so I did wrap it around the rounded edge and underneath. Still, one of the wallpaper strips did twist askew, and there was a small gap at one seam. With this pattern, no biggie – I just cut out a leaf and pasted it over the gap.

I told you the room had crazy angles!

Note that in papering angled areas like this, you can match the pattern in some places, but there will be mis-matches in others, such as where the sloped ceiling meets the fir-down. This wild pattern is perfect for disguising any mis-matches!

Rolling the paper out on the floor, to get an idea of the pattern’s layout .

Closer look at the lemons and leaves . And angles .
It looks like a Picasso painting, don’t you think? The homeowner wanted something wild and fun , to set off the white minimalism in the rest of the home .

The pattern is called Citrus and is by A Street Prints . It’s a nice non-woven material , doesn’t expand , and can be hung by the paste the wall method , although I opted to paste the paper , as I usually do.
Non-wovens are designed to strip off the wall easily and in one piece, with no / minimal damage to the wall when you redecorate . They’re usually a pleasure to install . They’re more stain resistant and more able to withstand humidity than many traditional wallpapers .

The home of this busy young family is in the West University area of Houston .

Modern Electrical Technology Makes Hanging Paper Easier

Bad photo, but I’m to put wallpaper in this room, including the tall and deep fir-down at the top right, which has two recessed light fixtures in it. You want the paper to go behind the light fixtures, not cut around them, if at all possible. In the photo, at the far middle left, you can see one fixture dangling by it’s wires below the fir-down.

Some of these recessed fixtures are tricky to take down (many won’t come down at all), but these ones turned out to be held in place by tension springs, which fit into sideways hooks, which you can see at the left inside the hole.

Here’s a closer look. These are the same type springs that hold the vent covers to exhaust fans in place. As you push them upward, they spread apart and hold the fixture securely in place. Easy-peasy! You can also squeeze the springs together and remove them from the mounting housing, which lets the fixture dangle from its electrical wires.

That’s what I’ve done here. Now it’s much easier to work the wallpaper around the fixture. But it could be made even easier – by removing the light fixture all together.

Most light fixtures have black and white wires coming from inside the wall that connect to black and white wires on the electrical fixture and are connected and held in place by a twist-on screw cap or wire nut. What’s very cool about this particular fixture’s electrical connections is that it’s made by this orange plug, which fits into the orange receptacle – no wires to twist or cap, and no need to cut off the power. It’s all simple and perfectly safe.
Here I’ve disconnected the two orange parts.

With the light fixture completely out of the way, it’s much easier to install the wallpaper, and no paste gets slopped onto the fixture.

Here’s the wallpaper installed and trimmed around the inside of the opening.
Oh, and don’t mind the slight pattern mis-match on the left … there were issues with un-plumb and un-level walls coming into play.

And here I’ve reconnected the orange plug parts, and placed the spring back inside those hooks, then pushed the light fixture up and back into place. Look at how nicely the flange (outer ring) of the fixture covers the cut edge of the hole and the wallpaper.