Outsmarting Bull Nosed / Rounded Edges / Arch

Looks nice, huh?

But these rounded edges , especially arches , have been a thorn in the side of wallpaper installer s since they became popular more than 10 years ago. Hanging paper on them and trimming neatly at the right point is difficult. Because the paper is hanging over the edge blocking your view of where you need to trim . A level or laser level don’t always work because the home’s framing isn’t always perfectly plumb . Metal straightedges / trim guides are useful, but can slip and mess up your cut. The arches present their own challenges because a straight edge won’t line up with them .

A colleague in the Wallcovering Installers Association ( WIA ) invented this gadget , which is a huge help. This is a 1.5″ section cut off from the 10′ length of bull nose corner bead used in the drywall construction of these edges. Then you cut notches in it at the point on the corner where you want to trim your wallpaper .

Some installers place a trimmer blade in the notch and slide the gadget along the edge, trimming as they go. I find that the thing wobbles too much for an accurate trim, plus it’s difficult to hold the blade while you’re sliding the thing down the wall. So I put a pencil point into the notch and draw a line along where I want to trim. Then I can use a straightedge and trimming blade , or a scissors, to cut along the line. Makes a nice, even, straight cut! Note that I like to wrap it about 1/3 of the way around the rounded edge.

OK, so you’ve seen how I trimmed along the edge to the right. Now here’s another trick that I’m going to use on the edge to the left, as seen in the photo. The wallpaper strip is 20.5″ wide. But I trimmed it vertically so that the piece over the arch is 10″ wide. That correlates to the point where I want to trim the strip that will land on the rounded edge going down the wall.
Note that I have not completely trimmed the part under the arch on the left side, because I want to be sure the cut edge lines up with that on the next strip I’m going to hang.
The blue plastic tape is there to keep paste off the wall paint . It will be removed after the piece is trimmed to fit.

Now here I’ve placed the remaining 10.5″ wide left section of the strip of wallpaper. You can see how it’s falling perfectly along the bull-nosed edge – saving me from having to use a blade or straightedge or gadget.
Note that this works only if the edge is perfectly plumb , and that the piece above the arch is also perfectly plumb, and my new strip is hanging perfectly plumb. This paper is a non-woven material, and is somewhat stiff and unbending , so not really amenable to twisting or tweaking into place. Plus, you want to keep that left edge straight, because your next / subsequent strip will need to butt up against it. Trust me, I did a lot of measuring and shooting the laser level before I pasted or hung any paper!
Now that it’s in place, I can go back and trim that remaining bit under the arch, making sure that it meets up in the corner with the edge of this piece .

Here’s another shot of it finished.

Closer up.

This tree branch foliage pattern is called Twining and is by Graham & Brown . I like most everything they make. The non-woven substrate is designed to strip off the wall easily and in one piece , with no damage to the wall , when it’s time to redecorate .
This home is in the Oak Forest / Garden Oaks / Heights neigborhood of Houston .

Modern Electrical Technology Makes Hanging Paper Easier

Bad photo, but I’m to put wallpaper in this room, including the tall and deep fir-down at the top right, which has two recessed light fixtures in it. You want the paper to go behind the light fixtures, not cut around them, if at all possible. In the photo, at the far middle left, you can see one fixture dangling by it’s wires below the fir-down.

Some of these recessed fixtures are tricky to take down (many won’t come down at all), but these ones turned out to be held in place by tension springs, which fit into sideways hooks, which you can see at the left inside the hole.

Here’s a closer look. These are the same type springs that hold the vent covers to exhaust fans in place. As you push them upward, they spread apart and hold the fixture securely in place. Easy-peasy! You can also squeeze the springs together and remove them from the mounting housing, which lets the fixture dangle from its electrical wires.

That’s what I’ve done here. Now it’s much easier to work the wallpaper around the fixture. But it could be made even easier – by removing the light fixture all together.

Most light fixtures have black and white wires coming from inside the wall that connect to black and white wires on the electrical fixture and are connected and held in place by a twist-on screw cap or wire nut. What’s very cool about this particular fixture’s electrical connections is that it’s made by this orange plug, which fits into the orange receptacle – no wires to twist or cap, and no need to cut off the power. It’s all simple and perfectly safe.
Here I’ve disconnected the two orange parts.

With the light fixture completely out of the way, it’s much easier to install the wallpaper, and no paste gets slopped onto the fixture.

Here’s the wallpaper installed and trimmed around the inside of the opening.
Oh, and don’t mind the slight pattern mis-match on the left … there were issues with un-plumb and un-level walls coming into play.

And here I’ve reconnected the orange plug parts, and placed the spring back inside those hooks, then pushed the light fixture up and back into place. Look at how nicely the flange (outer ring) of the fixture covers the cut edge of the hole and the wallpaper.

Wallpaper and Scrolly Jewelry

OK, so prepping walls and hanging paper, I can get pretty grungy by the end of the day. My usual outfit is shorts and a T-shirt.

But, gee, the Wallpaper Lady wants to look a LITTLE girly. Check out one of the new earrings I got at the Renaissance Festival this year. Big enough to see, but small enough to keep out of the way, pretty, but plain enough to work with shorts and a T-shirt.

So the other day I was putting on a hairband (seen at left), to keep the blonde mop out of my eyes, and – TUG TUG TUG!! The thin hairband had gotten itself looped around the swirl of one of my new earrings. It was in there tight, too! What happened in a split second sure got securely tangled. I had to take both of them off, to get them unscrambled.

The Well-Traveled Paperhanger

I do my wallpaper bids on Sunday afternoons. This works out well for me, because I’m not up on my ladder hanging paper. And it works out well for my clients, because, while Saturday is generally Errand and Chore Day, most people are around the house on Sunday afternoon.

Here’s how my day went yesterday:

Heights, Sping Branch, Memorial & Dairy Ashford, Katy, Sugarland, Pearland, Clear Lake. Whew!

I put 171 miles on my van (at 13 mpg), and was on the road from 10:00 am until 7:00 pm.

It sure felt good to get back home and put my feet up – watched the movie “Cool Running,” about the Jamacian Bob Sled Team in the Olympics. Good flick.