Posts Tagged ‘incompatible’

Wallpaper Coming Off – Delaminating Wall

January 14, 2022

An Unfortunate Situation

This Brooklyn Toile wallpaper by Flavor Paper on an accent wall in a nursery went up beautifully. The contractor had added new Sheetrock to one wall, and painted the other, old/original wall. I skim-floated both walls and sanded smooth, primed, and hung the wallpaper. Perfect! (Search here to see my original post.) But within less than a month, the homeowner contacted me and said that the wallpaper was ” coming off the wall .” It was a 1920’s bungalow in the Woodland Heights neighborhood of Houston. And therein lies the brunt of the problem.
The wallpaper itself is not ” coming off the wall .” What’s happening is that the wall surface itself is coming apart – or, delaminating . This is because multiple layers of paint and other substances on the wall may not be compatible. A probably scenario: In 1920 oil-based paint was used. Later someone rolled on a coat of latex paint. Then the homeowners redecorated and used gloss paint. Then some ” flippers ” who had watched too much HGTV slapped on more paint without bothering to de-gloss or prime first. And somewhere in the mix you’ve got cheap paint and dust and other incompatible materials.
Over time, and especially when stress is put on the wall surface, such as when wet wallpaper paste dries and the paper shrinks, this stress can tug at the wall and actually pull these layers apart. There are other contributing factors, too, such as humidity, temperature, and location. I find it interesting that the worst parts of the affected seams were toward the top of the wall. This speaks of heat, humidity, and forced air (either hot or cold) coming out of the air vent just to the right of this wall. This photo is of the area over a door, very close to the air vent.
See how thick that is? It’s not just the wallpaper. There are several layers of wall coming apart. Some layers are clinging to the back of the wallpaper, and some are staying stuck to the wall.
Multiple layers, many years of coatings on this wall.
Easy to see the many layers. The paper itself, my blue primer, my layer of smoothing compound, paint, more paint coming off the wall. Then multiple layers of paint and texture still clinging to the wall. This shot is just below the ceiling.
Same thing happening at the baseboard at the floor.
Layers of paint separating from the wall in chunks. Some pulled off easily, and some I had to chop off with my 3″ putty knife.
Most of the paint and unstable surface material clung to the back of the wallpaper. This pile is just three strips – only half the wall. But it’s thick and stiff and heavy because of the paint stuck to the back of the wallpaper. There was so much and it was so heavy and bulky that I had to carry it out to my van in two trips. When I got home, it totally filled my trash bin.
Here’s the wall once all the other layers came off. Brushing my hand over it revealed a layer of dust. No wonder the paint and other coatings wouldn’t stick. Nothing sticks to dust. It’s like flouring a cake pan… The paint or wallpaper will kinda stick – but won’t really stick. Paint on top may be fine. But add a little stress from drying / shrinking wallpaper, and you may end up with layers that pull apart.
Wiping the walls with a damp sponge removed a lot more dust. But the wall still felt chalky. Whatever type of paint this was, it was not holding together.
I had to stabilize this chalky surface. Enter Gardz, a wonderful product – Gardz is a thin, penetrating sealer that soaks into porous surfaces and binds substances together. It dries hard and creates an intact surface. The darker area in the picture is where I’ve rolled on a test area. Gardz is thin like water, and it runs and drips and splatters. It’s imperative that you cover floors, countertops, and baseboards, and roll carefully, and roll upward rather than downward, to minimize runs and drips. A microfiber roller holds the liquid well, and reduces drips.
Gardz is made by Zinsser.
No photo of the finished wall, but I was very pleased with the stability of the surface. No more chalk or dust. Now, there still could be unstable or incompatible layers deeper inside the wall. (Latex paint over oil without proper prep.) But for now I feel pretty confident that this wall is solid and will hold up to the next process in preparation for getting the new wallpaper up.

Don’t Use Adhesive Picture Hangers

January 6, 2022
Yes, they’re strong enough to hold a 50lb painting.
But removing them may well take layer(s) of paint along with! Here you see a bubble that has lifted from the wall, as well as a break in the paint that was torn off by the adhesive picture hanger.
Several layers of paint have been pulled away from the wall. This is called ” delaminating .”
One reason for this is because the original underlying surface may have been dusty – as in dust from construction, or from sanding new drywall joint compound. Nothing sticks to dust. Other reasons for delaminating walls are incompatible surfaces, such as, an older home that starts out with oil-based paint, then someone comes along and applies latex paint over it without proper prep, then someone adds a gloss paint, then a ” flipper ” buys the house and slaps on a coat of paint without deglossing, ,,, on and on, situations that can cause layers of paint to not stick to each other. End result is that the wallpaper may come away from the wall, too.