Patching a Hole Around a Pipe

You’re looking at a water supply line underneath a pedestal sink in a powder room.
This hole is a little wide, and offers the wallpaper nothing to adhere to. In addition, there is no escutcheon (decorative plate) to hide the hole.

I took some special paper and cut a ” collar ” to fit around the pipe and also cover the hole.

I dipped the “collar” into Gardz . This is cool stuff. It soaks in to porous surfaces, adheres to surfaces, and dries hard.

Here is the patch in place. Once it’s dry, I’ll skim-float with joint compound (” mud “) and then sand smooth.
The finished product will be a smooth, intact surface for the wallpaper to adhere to, with only a tiny gap around the plumbing.

Kill Point Over Door, Ridge, More

After you’ve hung wallpaper on all the walls in a room, the point where your last strip meets up with the first strip is called the kill point . This virtually always ends up in a pattern mis-match. That’s why you engineer to place it in an inconspicuous place, such as behind a door.
This powder room, though, had no hidden corner or handy door. That meant that I would have a pattern mis-match a full 5′ high, to the left of the toilet you see here. I prefer to have the pattern match in a corner like this. As you can see – it does. I will explain how I accomplished that.

I decided to place the kill point over the door. Even though this space is 2′ high and a mis-match might be noticeable, not many people are looking up over the door, so it’s a better choice than in a 5′ or 9′ long corner.
The dark smudges on the wall in the photo are where I’ve spread paint, to prevent white walls from peeking out, should the dark wallpaper shrink as the paste dries.

Here I’ve positioned the strip on the left. This leaves a gap of about 3″. Once I match the new strip up to the piece on the right, its pattern will not match perfectly with the strip on the left.

Now I’ve positioned both strips, and the one on the right is overlapping the one on the left.
Here’s an idea of what the pattern mis-match will look like. To be honest, it’s not all that bad, with this busy pattern and being up over the door. Still, I thought I could make it look better.
I’m going to do a double cut , which is our installers’ fancy term for a splice. I’m going to cut through the two strips, splicing them together, cutting along the vertical foliage elements, to minimize cut-off motifs and to disguise the splice.

When double cutting on the wall, it’s really important that you slice through the two layers of wallpaper only , and not cut into the primer or wall surface beneath. This is because, if the wall surface becomes scored or compromised, when the wallpaper paste dries and the paper shrinks and pulls taught, it can put tension on the wall surface. If the surface is not intact, it can give way and actually come apart ( delaminate ), resulting in wallpaper that comes away from the wall – and there’s nothing beneath it to paste it back to.
I’ve blogged about this before, so do a Search here to learn more. It’s important!
Anyway, to protect the wall beneath where I will make my splice cut, I’ve placed three layers of scrap wallpaper, to pad the wall. I figure I can cut through the two top layers, but not all five.
Note that three layers of non-woven material have some thickness, and can “throw off” the splice cut and prevent the top two strips from fitting together perfectly. In this case, the paper is flexible enough that I’m not worried about that particular scenario.

The strips are in place, and I’m ready to make my cut. I prefer to use a single-edged razor blade held in my fingers, rather than a blade-holder. What’s most important is that the blade be brand new and spankin’ sharp!

Here I’ve made my cut and am removing excess paper from the right side of the top strip. Look carefully and you can see how my razor blade followed the contours of the vertical foliage design elements.

Here I’ve removed the excess paper from the left edge of the bottom strip. You can see they are poised to fit together nicely.

Before fitting the two strips back together, though, I’m examining the wall surface. Check the photo carefully, and you’ll see that I did, after all, score into the primer. 😦 The surface below is skim-coat that was used to smooth a textured wall – and another potential layer that may come apart when exposed to tension from the drying wallpaper.
Shoulda used a Boggess Strip. https://www.steveboggesspaperhanging.com/lexanpage.htm

One way to prevent the wall from delaminating is to put something over the compromised area, to distribute the tension of the drying paper and take it away from the cut wall. Here I’ve taken a scrap of wallpaper, which is a tough non-woven material, and carefully peeled the printed surface from the white substrate (no pic of that process). Now I have a thin material that I can use to pad the wall.
I’m using the black printed side facing out, in case the spliced strips shrink a little – anything peeping out will be black and not noticeable.

Here is the bit of paper in place, spanning across the cut on the wall.

Now I’ve smoothed the two top strips back into place. Since my double cut followed along the vertical foliage elements as much as possible, and because I cut around the gold flowers to keep them full and round, the pattern looks like it matches up just about perfectly.
But wait! … What’s that lump / ridge under the wallpaper, the full height of the seam? That’s my seam padding! Doesn’t look great.
I’m really surprised at this. The non-woven wallpaper material is thick. But that’s why I pulled the top and bottom layers apart, to make my patch piece thinner. I guess not thin enough. Once dried, this ridge is going to be obvious.
But, to be honest, this is up over a door where no one’s going to be spending much time looking. In addition, once I get my 100 watt light bulb out of there and replace the homeowners’ original, small light fixture, this bump under the wallpaper will be pretty much indiscernable.

Still, that lump was buggin’ me. Another invention from my colleague Steve Bogges to the rescue! Pictured is his seam tape , which was made specifically for this type situation. This is very thin – yet strong – paper tape that is used to bridge cut areas like this, and prevent tension from drying wallpaper from tugging at unstable walls.
The tape has a pre-pasted side (the gloss you see), and feathered edges, to make it less noticeable under wallpaper.

Hard to see, but here I’ve placed the seam tape over the cut wall areas

Now the two top strips have been smoothed back into place. Amazingly, no bump from the seam tape beneath shows. And the pattern mis-match is barely visible, too.
Win-win!
All that’s left to do is to wipe paste off the surface of the wallpaper. This overlapping and splicing does mean that wallpaper paste will get on the surface of the strip underneath. Actually, there is a way to prevent that, and it also involves products from Steve Boggess …
But … that’s a blog post for another day …

This pattern is called Peonies and is by Rifle Paper.

Damage to Wall from Double-Cut, Pt I

while papering around a window, the previous installer used the double-cut technique, which is a fancy term for splicing two strips together. This is standard procedure, and he did a good job.

BUT … he failed to protect the wall surface beneath the splice. So his razor blade cut deep into the wall. You can see the crack in the photo.

The problem with this is that, now that the wall surface is not intact, it’s quite possible that the layers inside the wall (gypsum, paper, paint, more paint, wallpaper primer, etc.) can come apart from one another when the wallpaper paste dries and tugs at the wall surface.

In this photo, everything has stayed nice and flat. But very often, the split seam will curl back away from the wall. This looks bad and is difficult to repair.

A way to prevent this is to protect the wall before making the splice cut, by padding it with something to prevent the razor from scoring into the wall. Some people use old vinyl or scrap wallpaper. I like to use Boggess strips, which are flexible polycarbonate plastic strips that are impossible to cut through. Do a Search here to learn more about this cool invention.