Geometric on Tricky Outside Corner

OK, never mind the ’80’s-era toilet paper holder that’s recessed into the wall here and is not removable – which presents a challenge all its own. My issue is adding the next strip of wallpaper to the left, turning the corner, and keeping the pattern matched as well as possible in both the inside corner and around the outside corner.
Usually, when turning inside corners, you wrap the paper around the corner 1/8 of an inch, and then cut a new strip of paper, match the pattern, and then overlap it that 1/8″ . That helps eliminate issues like mis-matches or wrinkles due to crooked corners or uneven / bowed / out-of-plumb walls . (no walls are ever perfect )
But in this case, we also have an outside corner to wrap. Even though it’s only about 2″ wide, that edge can cause the pattern to go off-plumb , or to create wrinkles in the wallpaper .
Going against most rules of wallpapering , I’ve decided to wrap the next strip around this 2″ wide wall and then onto the wider wall to the left .

Here I am, starting to position that next strip. I’m not going to try to wrap a full 27″ wide strip around this turn. Instead, I’ve trimmed it vertically along a horizontal stripe , which makes this strip narrower and more easy to handle , and also will help in placement of the next strip.

Now I’m pushing it into place into that corner. Note how the paper is wrinkling, both on the wide wall, and as it comes around the 2″ wall.

Another shot of the placement and wrinkles .

Using my plastic squeegee smoother to press the paper tightly into the inside corner. Note that, since the corner isn’t perfectly straight or plumb, there were a few areas where I couldn’t press the paper tightly into the wall, but had to leave a bit of a gap or air bubble, in order for the left edge to wrap around the turn.
The plastic smoother can also be used to gently push out wrinkles on the larger body of the strip of paper to the right. Don’t press too hard , nor overwork , because you don’t want to stretch the paper – that will cause more wrinkles.

The plastic smoother took care of the inside corner. Here I’m using my damp microfiber cloth to tightly press the paper around this outside corner .

OK. Paper’s wrapped tightly around this corner – but, because the corner isn’t straight , we’ve got wrinkles and warps .

Sometimes, you need to take a scissors to make relief cuts to help ease the paper around the corner . Try to make your cuts along an element of the design , to make the slit less noticeable.

here is that little narrow bit, finally wrapped around the outside corner. Now we need to add the next strip to the left of this. Note that this narrow strip isn’t straight nor plumb nor equidistant from the corner that we just turned. Nor is it equidistant from the next corner we have to deal with, which is to the left (not pictured).
Since we want the wallpaper strips to match in the corners, it’s important that the wallpaper pattern fall in the corner to the left at the same point from ceiling to floor. Complicated to explain.

So I’m taking a fresh strip of wallpaper , made sure the pattern matches correctly , and have trimmed it vertically along the tan stripe . Now placing it along this wrapped edge.
Because I’m overlapping instead of butting , I’m able to pull the new strip to the right or left, to keep it equidistant from the right outside corner . Or, from the inside corner to the left.
Actually, I don’t care much about the right side. The eye won’t notice if the new strip isn’t perfectly plumb . Nor will it notice if the pattern match isn’t 100% perfect . But it will notice if the pattern doesn’t match perfectly in the inside corner to the left.
So I’m pulling and manipulating and overlapping the strip a bit, so that the left edge of it is exactly 10-3/4″ from the left edge. This ensures that the pattern motifs fall all at the same point into that corner on the left.
Do I can cut my next strip, trim it vertically so the design matches with that in the corner, and get a perfect pattern match in the corner. Kinda difficult to explain, but I hope you can follow what I’m describing.

Note that this overlap is causing a bit of a ridge under the paper . Hard to see here, but when the paper dries and shrinks tight against the wall, it will be a little more obvious. But I’d rather have a ridge on the right, than a pattern mis-match in the corner to the left.
Oh, and never mind that little pattern mis-match to the right … that’s the paper wrapped around the corner, so you’re looking at different dimensions, not a pattern mis-match.

Here is that strip finished. The vertical strips isn’t perfectly plumb, but no one can tell that.
ut the pattern is perfectly straight in the inside corner to the left . So when I take my subsequent strip and trim it vertically to remove the right edge by approximately 10-3/4″ , the pattern should match perfectly in this inside corner. (It did!)

This “sort of” Greek key trellis geometric design is by Thibaut , one of my favorite brands. It was on a triditional paper substrate , and was hung via the paste the paper method .
It was purchased from my favortite source for wallpaper in Houston , Dorota Hartwig at the Sherwin-Williams in the Rice Village , who has more selection books than anywhere else in the city – and knows what’s in every one of them! Call before heading over (713) 529-6515 .
The home is in the Champions Forest area of northwest Houston.