Posts Tagged ‘multiple’

Mess Stripping Wallpaper

February 6, 2021

Over the years, this powder room ended up with at least four layers of wallpaper. Some had been stripped down to the backing layer before the next layer went up, sometimes a primer was used, and in other cases, the installer simply plopped the new paper on top of the old.

The homeowners attempted to remove the multiple layers of paper. This mess would have been difficult to begin with, but, to complicate things, unfortunately, they pulled some bad information off the Internet. You can see how the use of a “paper tiger” scoring tool caused damage to the wallpaper as well as to the surface underneath – and didn’t help at all to loosen the old wallpaper.

My solution was to peel off the top layer of vinyl paper – the brownish striped faux finished pattern in the upper left of the photo. Then I used a sponge and lots of water to soak the tan backing until the paste reactivated and the paper could be scraped off the wall.

I would have preferred to also take off the layers of paper that remained underneath. But time was a consideration, and also the likelihood of damage to the wall surface. And I wasn’t sure if there was drywall or plaster under there.

So I used the product Gardz to seal off the revealed wallpaper. (Do a Search here on the word ‘Gardz” to learn more about this ingenious product.) Once that was dry, I skim-floated over the entire surface, to create a new, plaster-like layer. That was allowed to dry overnight.

The next day, I sanded this skim-float layer smooth. Because the smoothing compound had to be applied thickly, this resulted in a massive amount of dust. Luckily, it was all contained in the powder room, and was easily vacuumed up.

Then I used a damp sponge to wipe residual dust off the wall. This was followed by another coat of Gardz – a product that soaks in, dries hard, and effectively seals the surface. It’s a good sealer for new skim-coat, and it also works nicely as a primer under wallpaper.

With fans blowing on it, it dries quickly, and I was able to start hanging paper in an hour or so.

Dramatic Artemis Black Floral Completely Changes Dining Room

July 26, 2020


Like many newish suburban houses, this Clear Lake (south of Houston) home is all pretty much a homogeneous light tan – every wall, every room. This is the homeowners’ first venture into wallpaper – and, boy, did they make the right move!

This salad plate-scaled, brightly colored floral design on a black background amplifies this dining room accent wall many times! The pattern comes in other colorways, but none of those would have the impact of this black version.

The wall was textured, so I had to skim-float it and sand that smooth, then apply a primer. In the photo, you see where I have striped dark paint under where the seams will fall, to prevent the white primer from peeking through. I also used black chalk (see photo) to color the edges of the paper, to prevent the white substrate from showing.

This wallpaper pattern is a multiple / quarter-drop pattern match, which is very complicated to plot and lay out. The House of Hackney company made it easy, by providing this material in a 4-panel mural format. See photo

In one photo, you see the strips arranged in the order they will be hung on the wall. Before hanging, these will be re-rolled backwards, so the unprinted white backing side is facing outward.

This is a non-woven material, and I hung it using the paste-the-wall method. When I am on the ladder and unroll the strip and working to get it into position, having the paper rolled backward keeps the printed side from coming in contact with the paste on the wall.

Non-woven wallpapers have a high fiberglass content, and do not expand when wet with paste, nor do they shrink when drying, so less chance of gaps appearing at the seams, and also you can get accurate measurements that won’t change. The fiber content also ensures that the wallpaper “should” strip off the wall easily and in one piece when it’s time to redecorate.

A few short hours after I left, the homeowners sent me some “finished” photos. I wish I were more tech savvy and knew how to get photos off of text and into this post, so I could show you the gorgeous room. But for now, you’ll just have to use your mind’s eye.

Roiling Clouds Wallpaper in a Montrose Bathroom

July 4, 2019


Historic British manufacturer’s Fornasetti Line “Nuvolette” wallpaper pattern… I have long wanted to hang this paper, and finally got my chance today!

The walls in this first-floor bathroom of a newish contemporary styled home in the Montrose neighborhood of Houston were textured and covered with a semi-gloss paint. (top picture) It took me a day and a half to skim-coat the walls with smoothing compound, let dry, sand smooth, vacuum up the dust, wipe dust off the walls, prime, and let the primer dry. (second photo shows the smoothed and primed walls)

You would see this pattern better in a larger, less broken-up room, but here you can tell that it is a powerful depiction of roiling thunder clouds storming powerfully toward the west.

The product is unusual, in that it comes in a 2-pack set of “A” and “B” rolls. Each bolt is the same width and length as many Cole & Son papers. But the pattern is placed on those bolts very atypically, and the pattern match is equally unexpected.

Usually, wallpaper patterns match straight across from strip to strip. (straight across match) This means you see the same design element at the top of the wall on every strip. Or they drop down bit on every other strip, then pop back up to the top of the wall on the third strip. (drop match)

A much less common and much more complicated patter match is when the pattern motif repeats itself at the top of the wall only on every fourth (or more) strip. It can take a lot of mind-bending to figure out how to get the pattern placed correctly, and without wasting more paper than necessary.

Look at the upper left of the label, and it says that when placing the A strip to the right of the B strip, it’s a straight match. But when you position the B strip to the right of the A strip, it’s a drop match. This makes everything even wackier and more complicated!

What helped me here is that this home had plenty of room to roll out the bolts of paper, and plot out how the pattern would fall. (see photo) No one was home, so I had peace and quiet to concentrate and get my head around the intricacies of the pattern.

It turned out that the “straight match” indicated on the label was an error – no strips featured a straight match. Good thing I had all that floor space to roll the bolts out, so I could determine that.

Because the pattern match was so unpredictable, it was not possible to cut all of the “odd” and “even” strips ahead of time. And the very unlevel / unplumb qualities of the room also stepped in to make this impossible.

One thing that helped was that this was a non-woven material, which meant that the wallpaper did not need to be booked (left to sit and absorb paste and expand) before hanging. So as soon as I was able to figure out the pattern match for the upcoming strip, I was able to paste and hang the strip-in-hand.

If I had had to figure, measure, plot, paste, book, and then finally hang each strip individually, it would have taken a lot more than the eight hours it did take me to hang this 8-roll bathroom.

A big help on this pattern is that I belong to the Wallcovering Installers Association, and I check our Facebook page every day. (Sorry – it’s private … you can’t peek!) It was there that I learned about others’ experiences with this Nuvolette design, and how they tackled the pattern repeat and the install.