Good thing this family kept their scraps left over from the original install. They had a roll that had about two 8′ strips on it, plus a shorter piece that was maybe 4′ long.
Often, a repair means that you replace the whole wall, from corner to corner. For one thing, it eliminates the worries of color differences due to the existing paper fading from exposure to light over time. And the potential of buggering up one strip while removing the damaged strip next to it. And other issues like variables in the rate of expansion of wallpaper when it gets wet with paste, between what’s on the wall compared to the new replacement piece. Lots of factors.
Replacing the whole wall also would have eaten up all of the left over paper. I wanted then to keep that paper, in case something else happens down the road.
So I figured a way to use just 18″ or so of the shorter scrap they had left over.
First I took a razor blade and trimmed along a horizontal grass fiber, from the seam on the right, moving to the left and around the corner to where the paper meets the vanity. Then I peeled off the top layer, which was the grasscloth. That left the paper backing remaining on the wall.
I used a sponge to apply water to this backing, being very careful to touch only the paper and not the grasscloth that was to be left on the wall – water will stain grasscloth. After a while, the water reactivated the paste, and I was able to use my “dull” stiff 3″ putty knife to gently scrape the paper backing off the wall, making sure to get every bit that butted up to the grasscloth left on the wall, to be sure the replacement paper would sit flat against the wall and not on top of bumps of paper residue. All the while making sure to not damage the existing paper.
I cut a piece of replacement paper off the 4′ roll, cutting it a little longer than I might need, because I wasn’t sure if my first technique would work, and I wanted to avoid having to cut a whole new strip from that precious 4′ roll.
My first approach was to trim the replacement piece horizontally along the top reeds of grass. I hoped that this would butt up against the bottom of the strip on the wall. It did not. This is because the reeds of grass are uneven, and there were undulations between the top and bottom pieces that left gaps and overlaps between the two strips. (sorry, no photo)
I have used this technique successfully in the past. But that was with grasscloth that was coarser and had more distance between the reeds, so the eye would see the gaps as “normal.” Didn’t work with this finer textured grasscloth.
So my next option was to do a splice. What we in the trade call a double cut. A double cut will give you a perfectly fitted seam. But I try to avoid them, because there is the potential to score into the wall, which can cause an un-intact area that may delaminate over time, resulting in a “popped” seam.
(When hanging new wallpaper (not doing a repair to paper already adhered to the wall), it is possible to use polystyrene strips under the seam area to protect the wall when you make your cut. You can do a Search here to learn more about that.)
So a double cut was my best option. I had cut the replacement piece long enough that, after the failed attempt at butting the strips, I still had enough length to do the splice. I pasted the strip, let it book a few minutes to relax, and then unfolded it and ran a strip of blue plastic tape along the top edge. This tape will keep paste off the existing wallpaper. (Remember – grasscloth stains easily, and it’s difficult to wash, so it’s important to keep paste and other substances off of it.)
(The blue tape, and also the polystyrene strips and a lot of other cool tools, are available from fellow paperhanger Steve Boggess in Virginia. http://boggesspaperhangingtools.com/index.php )
Then I put the replacement strip in place, butting it up against the existing strip to the right, and overlapping the strip above it by about 3/4.” I used push pins to keep the strip from sliding. See 4th photo.
Next I took a single-edged razor blade and cut horizontally through both strips. Grasscloth is much thicker and harder than regular wallpaper, so I had to press hard to get through both layers – while still trying to not cut into the wall itself underneath.
Normally I would use a straightedge as a guide, but because the grass reeds are not straight themselves, I chose to free-hand the cut, following the horizontal line of one of the fibers of grass.
Once the cut was made, I removed the sections of paper that had been cut off. On the original piece that was already adhered to the wall, I had to pull off the grass, and then, once again, use my sponge and water to wet the remaining paper backing, reactivate the paste, and then carefully scrape that backing off the wall.
Once all that was done, as you see in the 5th photo, I peeled away the blue tape, and smoothed the two pieces together. They butted together perfectly!
The homeowner is going to paint over the little dabs of nail polish on the baseboard. (I told her I’d read her the riot act if she used remover or solvent and got any on that delicate grasscloth! 🙂 )
The Wallpaper Lady's Blog 