Kill Point Over Door

If you’re hanging wallpaper around a room with four walls and four corners , virtually always when that last strip of paper meets up with the first strip you hung some hours ago, you’ll have a mis-match of the pattern . That’s why we try to tuck this in an inconspicuous place like a 1′ high corner above or behind a door.
But sometimes you don’t have a hidden corner , and all four corners are highly visible and run the full height of the wall. In these cases, it looks much better for the pattern to match floor to ceiling , as you see in this photo. But you have to put the kill point somewhere!

In these cases, a more logical and less noticeable location for the mis-match is the shorter area over the door – where nobody is going to be spending much time looking at, anyway.
My first strip is on the left, and the rest of the powder room has been papered, and I’m working my way from the right to meet up with that strip on the left.

Here it is going into place. I’ve matched the pattern on this new strip to the strip on the left . The strip is too wide, and is overlapping the strip on the right. And, as expected, the pattern doesn’t match up on the right.
As an aside, that blue plastic tape you see at the top of the strip of wallpaper is to keep paste off the ceiling. Once I’ve trimmed that excess paper off, I’ll remove the tape , and the ceiling will be nice and clean – no paste residue to wipe off or worry that it will be visible or damage the paint / cause flaking .

Here I’ve trimmed that short strip at ceiling and above the door trim. As you can see, it’s overlapping the strip on the right, leaving a bump, and plus, the pattern doesn’t match .
To be honest, with this busy pattern and this short area up over a door , this 1′ of mismatch isn’t going to be very noticeable. But I wanted to make it look better.
I’m going to splice these two strips together.
In the photo above, the left strip is overlapping the strip on the right. I don’t like the way the pattern is lining up. A splice will leave branches cut off, and will be noticeable.

So here I’ve reversed things and have overlapped the strip on the right on top of the strip on the left . Now the pattern gives a better option for a splice . I like that there is a curved vertical tree trunk that I can cut along. This will help disguise the splice.

So now to do the splice, I have push hard enough on my blade to cut through two strips of paper. But it’s important to not score the wall surface beneath. When the wallpaper paste dries and the paper shrinks a tad, it will put tension on the wall surface . If that underlying surface is not unstable or not sound, due to being cut into, or dust is another factor , that tension can cause the wall surface to pull apart , and the wallpaper can come away from the wall. Actually, it’s not the wallpaper coming away – it’s the layers of the wall pulling apart.
So I use these thin flexible polystyrene plastic strips under where the splice will be. You can’t cut through them!

Here I’ve pulled the two strips of wallpaper away from the wall and am positioning the plastic strip under where the splice will take place. Next, I’ll smooth the two wallpaper strips back into place, with the right one overlapping the one on the left.

I like to hold a single edge razor blade in my fingers , but you can use a blade holder or trim knife , too.

Here I’ve free-handed my cut , trimming along the vertical tree trunk at the top , then straight down through blank area, then through some branches, and finally at the bottom again trimming along a curved vertical tree branch. Now I’m removing the excess from the left side of the trim / splice .

Lifting the strip on the right so I can remove the excess piece that was trimmed off on the right.

Now removing the polystyrene strip.

Using my plastic smoother to gently press the two trimmed strips of wallpaper into place.

Here it is all done. Trimming along the vertical branch at the top has helped disguise the splice. The bottom area doesn’t match 100% perfectly, but I’m OK with that. I’ll work on smoothing out that teensy overlap and the seam will be nice and flat.

All done!

The wallpaper pattern is called Luminous Branches and is by York . It’s non-woven / paste the wall material , and very nice to work with, durable , stain resistant , and will strip off the wall easily and with no damage when you redecorate .
If you’re interested in the source for the splicing / double cutting strips , or the thin blue tape to keep paste off the ceiling, please email me at wallpaperlady@att.net

Two Color Rhythmic Print for Heights Breakfast Nook

Before. Grey and boring .
The built-in banquette seating has been removed.

Finished.

Closer look.

Showing the pattern centered on the wall, and with the shutters. The dimensions of the paper not corresponding well with the width of the window, along with logistics of pattern placement at the ceiling line but starting my first strip under the window all created some plotting and engineering challenges. Fun, but time consuming. But it turned out great!

The original idea was to just paper the nook area, ending at the vertical door molding. But it would have looked odd to stop the wallpaper above this doorway. So the homeowner and I decided to run the paper along the top of the doorway, and then down the left side (not shown), which dead-ends into some cabinets and the granite countertop. It looked good and was the right call.

It tickles me that this is quite obviously a riff on the very popular Strawberry Thief wallpaper pattern by William Morris , which is quite popular right now (do a Search here to see my installations of it). When a company comes up with a hit, you can be assured that a competitor will soon be making its own version of it.
The original has a lot more color, but this version is limited to just two colors. Even though there is a lot of contrast between the black and the white , the pattern doesn’t feel busy, because the design is so close and tight .
There is a lot of symmetry , repetitiveness , and balance in Wm Morris and similar styles .

I love the raised ink texture to this material .

Whoops! A slight pattern mis-match . The overall design is busy enough that small imperfections like this (as well as some color variations / shading ) are not really noticeable .

It’s odd to me that the printing defects are different in different strips / rolls of the wallpaper . You’d think that if the print roller was out of whack, it would create the same image every time it strikes the wallpaper surface. Or maybe it’s the trimmers that are off. If they had cut 1/16″ more off that left edge, we might have a perfect pattern match .

The manufacturer is York , one of my favorites , in their Sure Strip line, also one of my favorites.
It’s in the Magnolia Home collection , by, yes, Joanna Gaines , of HGTV fame with the show Fixer Upper .
SureStrip is a pre-pasted , thin , flexible , non-woven material that is easy to hang . It’s also easy to remove when you’re ready to redecorate , because it’s designed to strip off the wall easily and in one piece with no damage to your walls .
installer houston birds

Popular Rifle Paper Peacock Pattern in Houston Heights Powder Room

In this townhome, the powder room is at the top of the stairs. The homeowner wanted something lively and dramatic to catch your eye as you walk from the garage up the stairs.

The bold and bright colors against a very dark green background, and fun flower and peacock design really answer the call!

Simply called Peacock Wallpaper , this very popular design is by Rifle Paper , which is manufactured by York , one of the oldest wallpaper manufacturers in the U.S.
It’s a non-woven , paste-the-wall material, and will hold up and resist stains very nicely for years to come.
N-W ‘s are also designed to strip off the wall easily and in one piece , with no damage to the wall , when it’s time to redecorate