Cool Trick Going Around Door

I’ve finished putting short strips of wallpaper over this wide entry way . My next strip will be a 9.5′ piece going down the left side of the door molding .

The piece above the door ended 1/4″ from the left edge of the door molding. Normally, I would butt my next strip up against the existing piece. Then, as I move down the wall smoothing the paper into place against the wall, there will be a 1/4″ bit of it that laps over against the full length of the molding. I would need to use a straightedge and blade to trim this off. And then use my damp microfiber rag to wipe paste off the molding.
This non-woven wallpaper is thick and stiff , and hard to press tightly against the molding, so a bit tricky to get a sharp , tight trim cut . And also difficult to ensure that exactly 1/4″ is being trimmed off . So it’s easy for the paper to go off-kilter , and for the pattern to not line up perfectly against the molding . Not a big deal on a busy floral pattern , but with a rigid geometric, it might be noticeable .

So I decided to try this. I wanted to pre-trim the strip to take away that 1/4″ . This would save me from having to do any pressing or trimming. And also ensure that the pattern would fall perfectly straight against the doorway molding.
I measured down 16″ (the height of the ” header ” over the doorway , plus a couple of inches for trimming at ceiling and then at the top of the door molding ) .
Then I used my straightedge , razor blade , and fine ruler (from Texas Art Supply ) to measure over 1/4″ and trim it off .
Don’t think this is a simple task … It’s hard to measure exactly the width of the bit above the molding that should be trimmed off. 1/4″? 3/8″? 5/16″?
Also take into consideration that most wallpapers expand when they get wet with paste . So that 1/4″ I cut off could extend to 5/16″ or even more. That would mean a gap along the door molding.
Next, if the strip above the door is not perfectly plumb , or if the door molding below it is not perfectly straight and plumb , the wallpaper won’t butt up properly against it, and may start to show a gap or an overlap.
Sometimes you can manipulate the strip of wallpaper so that it does butt up against the door frame. But that can result in warps and wrinkles , or a pattern mis-match of the next piece . Also, like I said, this particular non-woven product is thick and stiff, and not happy about being asked to twist into another shape. Pasting the paper – instead of pasting the wall – does help to make it more pliable , so you have a better chance of manipulating the paper as you want.

Here is the strip going into place. So far, it’s butting up nicely against the molding. And no need to trim anything or wipe paste off the woodwork – except for that little bit at the top, which was my ” extra ” allowed for trimming .
FYI, that dark stripe you see along the woodwork is a shadow.

Here is the wallpaper as it falls along the side of the molding. The pattern is lining up nice and straight and precise .
To be honest, at the lower 1/3 of the wall, the paper did start to torque out of shape , and wanted to leave a gap at the molding, which was trying to grow from 1/16″ to maybe 1/4.” Not a lot – but it sure would look bad to have a 1/4″ gap between the wallpaper and the woodwork.
Trying to “mush” it to the right to butt up against the woodwork was causing warps and wrinkles .
I was a little surprised, but the paste had caused the stiff material to become softened and pliable – just enough that I was able to gently work out all those warps and wrinkles , so the wallpaper laid nice and flat against the wall. AND the left edge didn’t become distorted, but fell nice and straight enough that the next strip was easily able to butt up against it nice and tightly.

This trellis / Moroccan lantern / onion dome / geometric pattern is by Designer Wallpapers .