Posts Tagged ‘plumbing fixtures’

No Sink Makes for an Easier and Faster Install Day

March 6, 2019


It’s hard to see in this photo, but there are two water line connections and a drain that were located under a wall-mounted sink in a small powder room.

Before I got started, the homeowner called a plumber to come remove the sink. This made it a LOT easier for me to get under there, and to cut around the plumbing fixtures. There are fewer cut edges, no mis-matched seams, and, since the area under this sink is exposed, the whole space looks neat and tidy.

It also means that the wallpaper goes completely behind the sink, with no cut edge at the top of the sink. So there are no worries about water that gets splashed onto the top of the sink wicking up under the paper and causing curling edges.

Most of the time, I trim around sinks in bathrooms like this. But when it’s possible to remove the sink, boy, it’s great for everyone! It makes my job easier and faster – it probably saved me an hour’s worth of trimming in this room. And it makes the job look better and ensures there will be no curling edges along the top of the sink.

AND it minimizes stress on the paper from manipulating it around bends and turns or overworking, so eliminates the possibility of creases in the material or flaking ink.

Win-win for everyone!

Advertisements

Wall-Mounted Faucets & Wallpaper

January 11, 2017
Digital Image

Digital Image

Digital Image

Digital Image


Trimming wallpaper around plumbing fixtures can be tricky, and with fancy-dancy wall-mounted faucets and handles, it can be a real trial. The builder of this new home understand that. Plus he wanted the wallpaper to be as seamless as possible, without a lot of relief cuts (cuts made in the paper to allow the installer to work it into difficult positions).

So he let me put up the paper before the faucet and handles were installed. It was much easier for me, and it gave him an intact wallpaper surface, so no worries about visible cuts or about water finding its way into seams and causing curling.

Sorry the 2nd photo is so dark. There are some visible relief cuts in the paper, but they are small and close to the pipes, and will be covered by the plumbing fixtures.

Tricky Bathroom Faucets

November 21, 2015

Digital Image

Digital Image


Needless to say, these plumbing fixtures should have been installed AFTER the wallpaper went up. It would have been much easier for me, and the paper would have gone right up to the pipes, eliminating relief cuts as well as the potential for paper to peel due to wicking of water into the substrate along those cut edges.

It would have been easiest for me to make three vertical cuts from the backsplash up to each handle / faucet, and then carefully trim around them. But that would leave three seams that were right where water will be splashed on them, opening the potential for them to absorb water and delaminate and curl, plus the possibility that the seams would be visible, and who wants three vertical seams 3″ apart?!

So what I did was, I made a horizontal cut from the right edge of the wallpaper to the center of the right handle, and then carefully trimmed around each fixture, while first making sure that, as the wallpaper came around the left side and then around the bottom of the faucets, that its horizontally cute edge met up with the horizontal cut I had made on the right. Meaning, that it met up with itself with no gaps of pattern mis-match.

Some of the fixtures were not tight against the wall, and I was able to slide the wallpaper behind them. In other areas, I had to trim right up against the metal. This always opens the potential for water to get behind and cause curling, so I used clear caulk to seal these areas.

This is a heavy vinyl wallpaper, which will be more durable than paper, because it is more resistant to water, which makes it a better choice for this particular application. Of course, if you want your faucets to come out of the wall, instead of the countertop, it would be best to put tile on the wall, rather than wallpaper. IMO

I was guestimating it would take about an hour to hang this one strip, but I think I finished a little quicker – say, 45 minutes. 🙂