Posts Tagged ‘razor’

Printing Defects – Serena & Lily Wallpaper

March 6, 2021

Obviously, the factory’s printer or its trimming rollers got off-kilter, creating this pattern mis-match at the seams.

It might have been possible to use a straightedge and razor blade to trim off 1/16″ from one edge. But since the mis-match ran off at a diagonal and was inconsistent throughout the bolt, that would have been extremely difficult and time consuming.

We sent the paper back, and requested new paper from a different run. When the paper arrives, I will visit the clients’ home before the install date to check the paper to be sure the pattern matches correctly.

What a disappointment! The walls are all prepped, the homeowners have dismantled the powder room, and were anticipating a beautiful, fresh new look by the weekend. 😦

S&L is one of my favorite companies, so this is doesn’t make me happy. But it appears that the company is quick to rectify problems with minimal hassle. New paper, from a different run, is already on its way!

ADENDUM: The new paper – from a different run – did arrive. I checked it, and it also had the same printing defects, although not as severe. Very disappointing. Interestingly enough, I have another client using this same pattern but in a different color just yesterday (March 17th). Her paper had NONE of these defects. It’s hard to understand what the colorway has to do with printing problems… But I guess that is a factory issue. See my post of March 20, 2021 to see how this finally turned out.

The 2-Hour Wall

January 9, 2021

Re my previous post, the wall in the photo above took me a full TWO HOURS to get three strips of wallpaper onto.

Part was access – narrow space, difficult to maneuver the ladder, squeezing around the toilet, wall height a little taller than I could reach comfortably,,, for starters.

But the main issue was wrapping wallpaper around this jutting wall with its two outside corners.

You’re not supposed to wrap wallpaper around outside corners, especially with a double corner as pictured here. The reason being that framing, drywall, corner beads, and all sorts of other construction components are never perfectly straight or plumb or level. Thus, attempting to wrap wallpaper around them will usually result in various things – the paper going off-plumb, the paper warping or developing wrinkles, the far edge of the paper twisting and not being straight so the next strip cannot butt against it without gaps and overlaps, stretching the paper to force it to cooperate, which will result in it shrinking when it dries and exposing gaps – among other unfortunate situations.

I did run into some of that in the instance pictured above. This new (and expensive) home had walls that were more “off” than most, with one corner being off by a full 3/4″ over a drop of only 9′. On this particular wall, the paper developed a pretty sizeable wrinkle toward the bottom 1/3 of the wall. I had to find a way to relieve wrinkle by eliminating the excess paper, while still keeping the left edge of the strip intact and straight, so the subsequent strip could butt up against it.

My solution was to cut through the paper vertically along the right edge (along the edge of the wall’s outside corner), about 1/4″ in from the edge, and from the floor to about 3′ up. Then I pulled the strip away from the wall, which enabled me to work out the wrinkle, making sure to maintain the straight edge along the right.

I smoothed the strip back against the wall, again, easing out the wrinkle. The excess from the wrinkle moved to the right, and left a bit of wallpaper hanging over the corner to the right. I used a straightedge and very sharp razor blade to cut off this sliver of excess.

This method did mean that there was a bit of an overlap, and thus a bump / ridge, along the right edge. I was worried that this would show, especially with the somewhat shiny paper, as well as light shining unforgivingly from the fixture to the left (not pictured). But once it was all done, the small overlap was barely noticeable. And definitely better than a large wrinkle.

Because I was able to keep the left edge of the strip straight, the next strip butted against it very nicely, with no gaps or overlaps.

I will mention that it also did help that this particular paper was a bit more flexible and fluid than many non-woven materials. Also, because I pasted the paper instead of the wall, the paper had a chance to relax and become malleable. The primer I used gave it a solid surface to cling to, so there was no shrinking or gapping as it dried.

These three strips on this one wall took me two full hours.

Whoops!

December 23, 2016

Digital Image

Digital Image


Slight injury on the job.

Actually, getting cut by a razor is pretty common. You just have to catch the blood before it gets on the wallpaper (it will stain it), and then wait a few minutes ’til it stops bleeding.

Then, on with the show! 🙂