Stuck in the Dots

Thibaut’s “Union Square” is a smart-looking and much more affordable alternative to Phillip Jeffries’s “Rivets” grasscloth.

Unfortunately, today, both the white label and the brown cardboard from the protective “end caps” got stuck in the raised plastic “dots.” The residue could not be removed completely.

In today’s job, with the low ceiling height, I could normally get three 8′ strips out of each 24′ bolt. But with this issue, because I had to discard the first 6″ or so, I could only get two strips.

Maybe if they wrapped the bolt in plastic or waxed paper before adding the label, it would prevent this.

I emailed their customer service rep … Thibaut is much more concerned and responsive than lots of other companies, so let’s hope they listen and put some thought into this.

Affordable “Rivets” In Contemporary New Home Office

This “dots and blocks” or “rivets” pattern is pretty popular. Phillip Jeffries makes one called “Rivets” and Thibaut has a similar one called “Union Square.” These are both textured products on grasscloth. (Do a Search here to see my installations of both of these.)

This version is 1-dimensional, but with the added fun of shiny metallic-like Mylar.

It’s printed on a dimensionally-stable non-woven backing, and can be hung by pasting the paper (which I did) or pasting the wall.

The manufacturer is A Street Prints, in the U.K.

3-D “Rivet” Squares on Grasscloth in a Home Office

Phillip Jeffries’s “Rivets” pattern is popular and trendy. The wallpaper I hung today is Thibaut’s response to it.

Thibaut’s version offers the same texture and appeal of real natural fiber grasscloth, as well as three-dimensional squares that unite to form larger squares.

Thibaut’s version Union Square is better because:

1.) Less expensive

2.) Better color consistency (fewer paneling and shading issues)

3.) Squares form a more muted secondary pattern, so it’s much easier to live with (the pattern doesn’t hit you in the eye every time you look at a wall)

4.) Squares are positioned on the strips so the installer can easily manipulate the pattern to accommodate un-plumb walls and un-level ceilings.

5.) For similar reasons, the installer can “tweak” the design a bit to ensure favorable placement of the squares (to eliminate having to cut through any of the squares, or bend them around a corner). Read below.

6.) When it’s unavoidable to have to cut through the squares, the Thibaut 3-D material is much easier to get through with a blade or scissors than the PJ or the Schumacher products.

7.) The bolts are marked in the order they came off the printing press (see photo), so you can hang strips sequentially, to minimize shading and paneling (do a search here on those terms).

8.) Thibaut provides clear tips on how to work with natural materials and what to expect with the finished outcome.

9.) Thibaut offers to replace material lost to working around defects, and they will also reimburse an installer for (part) of his labor, if a product is defective.

10.) Other points which are escaping me right now. But suffice it to say, despite its grand reputation, Phillip Jeffries products are often extremely difficult to install, and disappointing in appearance, and customer service is basically, “We never had this problem before – it must be the installer’s fault.”

Thibaut, on the other hand, researches what it takes to make a good product, does test hangs, and, if there is a problem, Thibaut actually listens to feedback from us installers.

In the window photo, I did some tweaking to get the rivets to line up exactly over the middle of the window. It took some further tweaking to position the squares so they would march down either side of the window at the same distance from the edge.

How did I accomplish that? After much measuring and plotting and a few practice strips, I widened the distance between two sets of squares over the center of the window – by a full inch. 4.5″ instead of 3.5″ is a big difference, yet it is barely noticeable. What is more important is that the squares going down either side of the window are all 3/4″ from the edge.

This home is in the Briar Park neighborhood of Houston – interestingly enough, right next door to another home I papered a year or so ago, and a block away from another home I where I hung paper in the powder room and have more bathrooms to paper coming up … In fact, I have put wallpaper in a whole lot of homes in this one tiny neighborhood. Near Beltway 8 / Sam Houston Tollway and Briar Forest.

The interior designer is Layne Ogden of Layne Torsch Interiors.

Three-Dimensional Square “Dots” on Pale Neutral Grasscloth

Thibaut’s “Union Square” wallpaper pattern is a response to the popular Phillip Jeffries’s “Rivets.” Thibaut’s looser design and pattern placement make it much easier to align with the walls and woodwork – including rooms that are out of square and out of plumb. Which is just about every house in every neighborhood in every state.

The 3-D squares are made of some kind of plastic stuff, and are virtually impossible to cut through with a razor blade or a scissors (such as when trimming at the ceiling door or window moldings). I was able to engineer the room so that I did not have to cut through any of those rivets! Because the PJ pattern is much tighter, this would have been virtually impossible.

Also, I found that my soft short-bristled smoothing brush worked well enough to press the material against the wall while skimming over the 3/8″ high square bumps (sorry, for some reason, the photo did not turn out). But my beloved plastic trapezoidal squeegee smoother was just about useless, because it would not accommodate the 3-D “rivets.” So I had to adjust my install tactics a bit, and figure how to get along without the plastic smoother.

This wallcovering is made of grasscloth, which provides the subtle texture that homeowners are loving these days. But because grasscloth is made of natural fibers, there can be a lot of variations between bolts, and even between strips off the same bolt.

For that reason, Thibaut not only notes the run number of a bolt of wallpaper, but also the sequence in which the material was produced (see photo). The idea is that if you hang strips sequentially, you will see less shading or paneling (difference in color between two strips of wallcovering). Thibaut’s insert also includes a LOT of jargon about the color differences inherent to natural products, and the admonishment to use the bolts and strips sequentially.

I used three double rolls / bolts of grasscloth for this entry. Two of the bolts (the first two in the sequence) were pretty homogenous in color. The room was small and had low ceilings, and so I was able to keep the three strips needed for the longest wall all from the same bolt (#1).

I cut my other full-length strips from the second bolt (#2). That left the third bolt (#3) for the many short pieces needed to go over the four doorways in the room. As you can see from the last two photos, even though it was the same run number and printed at the same time, this third bolt was noticeably different in color from the previous two. The background color is the same, but there is a lot – a LOT – more dark brown fibrous material that got worked into the woven grass material.

Keeping these darker strips over the doors was a good way to minimize this color difference. The strips were only 9″ high. If these strips had been placed side-by-side on an 8′ high wall, the color difference would have been abruptly noticeable.

Color variations are to be expected with grasscloth, or any natural product. But helpful labeling by the manufacturer, and careful plotting by the installer, can minimize these differences.

This ’60’s-era ranch-style home in the Briargrove neighborhood of Houston is very much a “sea of tranquility,” as the whole house is entwined in off-whites, creams, and tans, with various textures like rough wood, sisal, and this grasscloth, used to pull in depth and warmth.

The interior designer on this project is Layne Ogden, of Layne Torsch Interiors.

Phillip Jeffries Rivets Grasscloth Wallpaper

Digital Image

Digital Image

Digital Image

Digital Image

Digital Image

Digital Image

Digital Image

Digital Image

The Rivets pattern by Phillip Jeffries is pretty popular in the higher-end market (with lots of knock-offs by less pricy brands). It’s a fairly fine grasscloth with a handsome cross design made of 3D “rivets.” The rivets are made of something like vinyl, and are somewhat difficult to cut with a razor blade or scissors. Thank goodness they are not made of real metal!

I hung this in a small vestibule that leads to a powder room in a home in River Oaks (Houston). When you walk in the front door, this is the first thing you see, and it makes a stellar impression.

This wallpaper was bought at below retail price from Dorota Hartwig at Southwestern Paint on Bissonnet near Kirby. (713) 520-6262 or dorotasouthwestern@hotmail.com. She is great at helping you find just the perfect paper! Discuss your project and make an appointment before heading over to see her.

Wallet-Friendly Rivets

Digital Image

Digital Image

Digital Image

Digital Image

These homeowners loved the look of the “Rivets” by Phillip Jeffries. (Google it) But that product is way pricy. The interior designer found this similar pattern in a good quality paper, at a much more pocket-friendly price.

I hung this on an accent wall in the bedroom of a pre-teen boy, in a new home in Cypress (NW Houston). The furniture in the room is what you’d call “industrial contemporary” – all brushed / distressed metal, clean lines, with an urban edge. The wallpaper is the perfect backdrop!

The interior designer is Pamela O’Brien of Pamela Hope Designs, and the wallpaper manufacturer is Thibaut, one of my favorite brands.