Cool Trick Going Around Door

I’ve finished putting short strips of wallpaper over this wide entry way . My next strip will be a 9.5′ piece going down the left side of the door molding .

The piece above the door ended 1/4″ from the left edge of the door molding. Normally, I would butt my next strip up against the existing piece. Then, as I move down the wall smoothing the paper into place against the wall, there will be a 1/4″ bit of it that laps over against the full length of the molding. I would need to use a straightedge and blade to trim this off. And then use my damp microfiber rag to wipe paste off the molding.
This non-woven wallpaper is thick and stiff , and hard to press tightly against the molding, so a bit tricky to get a sharp , tight trim cut . And also difficult to ensure that exactly 1/4″ is being trimmed off . So it’s easy for the paper to go off-kilter , and for the pattern to not line up perfectly against the molding . Not a big deal on a busy floral pattern , but with a rigid geometric, it might be noticeable .

So I decided to try this. I wanted to pre-trim the strip to take away that 1/4″ . This would save me from having to do any pressing or trimming. And also ensure that the pattern would fall perfectly straight against the doorway molding.
I measured down 16″ (the height of the ” header ” over the doorway , plus a couple of inches for trimming at ceiling and then at the top of the door molding ) .
Then I used my straightedge , razor blade , and fine ruler (from Texas Art Supply ) to measure over 1/4″ and trim it off .
Don’t think this is a simple task … It’s hard to measure exactly the width of the bit above the molding that should be trimmed off. 1/4″? 3/8″? 5/16″?
Also take into consideration that most wallpapers expand when they get wet with paste . So that 1/4″ I cut off could extend to 5/16″ or even more. That would mean a gap along the door molding.
Next, if the strip above the door is not perfectly plumb , or if the door molding below it is not perfectly straight and plumb , the wallpaper won’t butt up properly against it, and may start to show a gap or an overlap.
Sometimes you can manipulate the strip of wallpaper so that it does butt up against the door frame. But that can result in warps and wrinkles , or a pattern mis-match of the next piece . Also, like I said, this particular non-woven product is thick and stiff, and not happy about being asked to twist into another shape. Pasting the paper – instead of pasting the wall – does help to make it more pliable , so you have a better chance of manipulating the paper as you want.

Here is the strip going into place. So far, it’s butting up nicely against the molding. And no need to trim anything or wipe paste off the woodwork – except for that little bit at the top, which was my ” extra ” allowed for trimming .
FYI, that dark stripe you see along the woodwork is a shadow.

Here is the wallpaper as it falls along the side of the molding. The pattern is lining up nice and straight and precise .
To be honest, at the lower 1/3 of the wall, the paper did start to torque out of shape , and wanted to leave a gap at the molding, which was trying to grow from 1/16″ to maybe 1/4.” Not a lot – but it sure would look bad to have a 1/4″ gap between the wallpaper and the woodwork.
Trying to “mush” it to the right to butt up against the woodwork was causing warps and wrinkles .
I was a little surprised, but the paste had caused the stiff material to become softened and pliable – just enough that I was able to gently work out all those warps and wrinkles , so the wallpaper laid nice and flat against the wall. AND the left edge didn’t become distorted, but fell nice and straight enough that the next strip was easily able to butt up against it nice and tightly.

This trellis / Moroccan lantern / onion dome / geometric pattern is by Designer Wallpapers .

Geometric Grasscloth in Home Gathering Area

No, this large room with sink and counters isn’t a kitchen. The family loves to entertain both family and friends, so included this “bonus” room in their new home’s plans. It’s used for both entertaining and crafting.
The wall facing you was originally painted a semi-gloss navy blue. In the photo, I’ve applied my wallpaper primer.
It will adhere to the glossy paint, and provide a matt finish for the wallpaper paste to grab ahold of.

Taking measurements and plotting the layout.

This paper has a selvedge edge , which has to be trimmed off by hand with a straightedge and razor blade. The manufacturer has not provided trim guide marks , so I am using a ruler and my eye.

The new look is so dramatically different I couldn’t resist taking a photo mid-hang. As you can see, I’ve used dark paint to stripe under where the seams will fall, to prevent any of my primer from showing through at the seams.
You can see the ceiling line starting to track upward on the right portion. More on that below.

Finished. Perfectly centered.

This is the mounting hardware for the big screen TV . I asked them to remove the TV, but we left the mounts in place. In order to support the heavy TV, they are placed quite securely into the wall , and I feel it’s best not to jimmy around with that.
Rather than have the first strip straddle the TV mount, I plotted to have my first seam fall down the middle of the wall, placing a seam in the mid point of the mount. This meant I had to hang four strips instead of three, but it made it a whole lot easier to work around the TV mount, as well as to keep the left and right edges of the grasscloth straight and plumb.

Close up showing the texture of this grasscloth material. It’s atypical to have grass cloth printed with a pattern , and I rather like the way the ink looks somewhat scratchy against the rough background.

Because it’s Schumacher, you can expect printing defects . The slight pattern match doesn’t bother me, as there were many more places along each strip that matched up perfectly. Nor do I mind the different intensity of ink on the two strips. That’s all part of the look of grasscloth.
But I wasn’t pleased with the white ink out in the middle of nowhere, as seen about 1//3 down the center of the picture. This isn’t considered a defect , and from a distance it’s not really noticeable. But it bugged me.

So I used some water-based paint and a very small brush from the craft store and lightly touched up the spots.

I also softened the mis-matched edges a bit. There’s a fine line between covering the white spots and staining the material, so use a light hand. And never permanent ink or oil-based markers or pastels.

Likewise, the ceiling line was not level, so as I moved from the mid-point out to the right, the ceiling rose above the geometric motif’s top edge, and a white line began to be visible, but only to the right of the centerpoint.

So I used the black paint to cover up that extra bit of white. This increases the width of that horizontal navy blue line from 1/4″ to about 1/2″. But from down on the floor you can’t tell, and it looks a whole lot better than having white on the right side and none on the left.

The brand is Schumacher and the home is in the Garden Oaks / Oak Forest area of Houston.
The interior designer who came up with this bold and lively look is Clayton Brooks .

More William Morris Strawberry Thief in Houston Heights Hall Bathroom

Because I feared unstable walls in this 1920’s bungalow in this neighborhood (do a Search for previous posts), before hanging the decorative wallpaper, first I hung a non-woven liner paper on all the walls. That’s the white material you see in the photo.
The liner was hung horizontally so its seams can’t line up with the decorative paper. The idea is to disperse tension from drying wallpaper and changes due to humidity and etc., so as to deflect tension away from sketchy wall surfaces, and thus prevent delamination of multiple unstable layers deep inside the wall. Again, do a Search here to learn more.

Finished vanity area, with pattern centered on the light fixture.

Corner shot.

This colorful and symmetrical pattern is quite popular; I’ve hung it a number of times just this year.

Englishman William Morris designed wallpaper and fabrics during the late 1800’s and early 1900’s.
The styles then were Art Nouveau and Arts & Crafts. This design reflects a bit of each.

Wallpaper expands when it gets wet with paste, and then can shrink just a tad as it dries. The liner helps prevent that, but you can still end up with teeny gaps at some seams.
To prevent the white backing from showing through, I run a stripe of dark paint under where each seam will fall.

I use matt finish craft paint from the hobby store, diluted with a little water (in the orange bottle cap) and smeared on the wall with a scrap of sponge. Use a ruler or level and a pencil to mark where you want to stripe the dark paint.
Remember to allow for that expansion as the paper absorbs moisture from the paste. Meaning, if the paper is 20.5″ wide, and expands 1/2″, you’ll want to run your line at about 21.” And make sure that your painted swath is about an inch wide.
I also run a bit of dark chalk along the edges of each strip, to prevent the white substrate from showing at the seams (no photo).

Morris & Co. makes this iconic Strawberry Thief.
Interestingly enough, most times when I’ve hung a Morris paper, it’s been a non-woven paste-the-wall material.
Today’s option was a surprise – a traditional British pulp . This is a pretty basic and somewhat old-fashioned type of substrate . Sort of like construction paper, or the pages of an old family Bible .
The paper is very fragile , and can tear easily. You have to keep using new razor / trimming blades, because the material dulls blades quickly, and when dull they will drag and tear the paper.
Pulp papers also require a soaking / booking time after pasting , to allow time for the material to absorb the paste , soften a bit, and expand . The edges of the strips like to dry out , so I’ve learned to dip about 1/4″ of the booked ends ( booked means the pasted side of the wallpaper strip is folded onto itself, bottom edge folded up and top edge folded down to meet in the middle), into a bucket of clean water.
Then it goes into a black plastic trash bag to soak and relax for a few minutes before hanging. I use this opportunity to paste the next strip.
Non-woven wallpapers have advantages, because they do not expand when wet, and therefor you can get accurate measurements. They also can be pasted and hung immediately, with no waiting time. Alternately, you can paste the wall .

Mural’s Too Short – Filling The Gap

The homeowner purchased this graffiti mural before consulting with me, and didn’t realize that it was not tall enough to fit the 9′ high walls in her sons’ room. So here you see the 4.5″ gap along the bottom. At first she was just going to leave it, because once the beds got pushed back into place, most of this gap would be hidden.

But I wanted to cover up the gap. The mural was too short for the wall, but it was also too wide. That meant we had a full unused 29″ wide panel to play with. There was a section that had a lot of asphalt area. So I took my straightedge and a razor blade and ruler and trimmed strips that were 5″ high.

Here I am applying the strips over the gap. I’m using clear adhesive latex caulk along the top edge of the strips where they overlap 1/2″ along the bottom of the mural … The surface of the mural is vinyl, and wallpaper paste doesn’t like to stick to a slippery surface like vinyl. The section that matched the asphalt in the mural best I placed in the center of the wall, where there would be a small space between the two beds. The beds look like race cars, BTW.

Here it is finished. From a distance, you would never think that the bottom was pieced in.