Posts Tagged ‘sequentially’

“Etched” Foresty Look in a Baby’s Nursery

September 22, 2019


This “Bellwood” mural by Rebel Walls is very similar to the “Etched Arcadia” mural by Anthropologie (do a Search here to see my previous installations). Either way, this is a wonderful idea for a nursery, and a cool alternative to the usual pink flowers or dinosaurs that many parents choose.

This mom-to-be was originally uncertain about papering the 3-walled alcove (which will house the changing table) (see third and fourth photos), because someone planted the idea that it would get soiled quickly. I’m glad I convinced her to take the plunge – the room really does look better with both the accent (crib) wall papered, and the changing table nook.

This product is a mural, and came in panels that had to be hung sequentially (as opposed to regular wallpaper with a repeating pattern). No photos of the plotting involved, but you have to roll the panels out on the floor to ensure the correct sequence. I made sure to center the low part of the pattern around the changing table, so the high part of the trees cradled it on either side of the niche. I really like the way this turned out.

Additional plotting was required to plan the area over the door and then the 1 1/2″ wide space to the left of it (not shown). All this measuring and plotting has to be done before the homeowner orders a custom-sized mural like this. Another reason to have the paperhanger see the room BEFORE you order your paper.

This paper is a non-woven material, and has a high fiberglass content. That makes it easy to remove when it’s time to redecorate, but it also makes it easy to clean in the case of accidents.

So this mom should go on to change diapers with confidence, all the while enjoying the unique look of her baby’s nursery.

This home is in the Garden Oaks neighborhood of Houston.

The textured walls were smoothed by the painting company, CertaPro. Usually I insist on doing my own prep, but it worked for the homeowner to have the paint crew get the messy smoothing part out of the way. AND … I know the CertaPro guys, and I knew I could trust them to do a good job. And they did. All I had to do was apply a wallpaper primer, and then hang the paper.

After 30 Years, It’s Time for an Update

December 19, 2018


These homeowners were updating their 30-year old home in Sugarland. To the dining room and hallway, they added crown molding at the top and wainscoting with block-and-panel molding at the bottom. Fine moldings add a real touch of elegance.

But the wife has a bit of a renegade spirit, and really likes the new “industrial modern” decorating style. So it was time for the ’90’s era faux-finish wallpaper to go – along with the border which you can just see a tidbit of it peeking out from under the new crown molding.

The new wallcovering choice is a small “flame” textured vinyl in a steely grey/taupe/gold color. It perfectly pulls together the industrial modern light fixture and the classic paneling.

The cut edges of the textured vinyl, along with the sheen of the material, really reflect light and bounce it around the room.

Like most solid-colored wallcoverings with no pattern, with or without a texture, this selection was subject to some color differences between strips. The dining area with 5′ high walls went up with a very homogenous look. Ditto one wall of the 8′ high hallway to the right. But another wall in that same hallway showed some differences between strips.

To minimize these differences, I tried various things.

First, I made sure to hang each strip sequentially, as they came off the bolt. That would reduce color variations, if the ink had gotten lighter or darker as the printing process went on at the factory.

I colored the edges of the vinyl with chalk of a matching hue, so that if a “high” area of the textured vinyl butted up against a “low” area of the next strip, the white edges would be covered with a matching color.

Next I tried reversing every other strip. This means you hang one strip right-side-up, and the next one upside-down. This ensures that one edge of the paper is being hung against itself, so, if there is a color difference, it is gradual instead of abrupt. Difficult to explain, but it makes sense if your mind’s eye can follow it through.

Interestingly enough, reversing every other strip worked quite nicely on the dining room walls, as you see in the photo. But in the full-height walls to the right, reversing the strips resulted in paneling. So there I hung all the strips right-side-up – and it looked great.

But on the far wall, no matter if I hung right-side-up or reversed, you could see differences between the strips (last photo). I replaced one strip once, and another I replaced twice – but never really loved the way it turned out. On some of the other seams, even though I had colored the edges with chalk, the white vinyl still showed. At some point, you just have to say, “This is how the product is.”

This is also why you discuss this with the homeowner before starting the project – and hopefully before she makes her decision to purchase this product. In this case, the homeowner was originally looking at grasscloth – and that product would most likely have had much more noticeable color differences.

Lighting has a lot to do with it, too. Strong light, filtered light, incandescent or LED, light straight-on or light from an angle, all put their thumbprint on how the wallpaper looks.

This wallpaper pattern is by York (one of the homeowners is originally from York, Pensylvania!), and was bought from my favorite source for good quality, product knowledge, expert service, and competitive price – Dorota Hartwig at Southwestern Paint on Bissonnet near Kirby. (713) 520-6262 or dorotasouthwestern@hotmail.com. She is great at helping you find just the perfect paper! Discuss your project and make an appointment before heading over to see her.

Farrow & Ball Branding, Sequence

March 13, 2018



Farrow & Ball (who manufacturers the “Lotus” wallpaper design in my previous posts), is a British company, and they do things properly and meticulously. I liked their labels and the trademark design on the box their paper comes in. The box is corrugated cardboard and cushioned to prevent damage to the edges of the wallpaper rolls.

Each roll is individually wrapped, too, with it’s own sticker. Going further, note that each of those bolts is numbered, indicating the sequence in which it was printed. The idea is that each strip of paper should be hung sequentially. This will minimize any color differences related to ink as it works its way through the press.