This is some novel stuff!
This wallpaper pattern is something like a mural, but with a little more brain-bending. It is one continuous design, with no element or motif repeating or showing up more than once in the 33′ length of each bolt.
It’s a good thing that no one was living in the house, and that furniture had not been moved in yet. Because I needed a LOT of floor space to roll out and study each bolt.
I had to compare the height of the walls and the length of each strip that I needed, to the placement of various animals in the design. This enabled me to plot where on the wall any given critter would appear, and to get as many creatures as possible on each strip, all while accommodating the homeowner’s preference for a few special ones.
I rolled the entire 33′ long bolt out on the floor, took measurements, and used blue tape to indicate the tops and bottoms of each strip. This enabled me to fiddle with various layouts and animal positions, and I could make changes if needed.
We needed 22 strips, and I was getting 5 strips out of each double roll bolt. So after I cut five strips from the first bolt, I moved on to the second bolt.
To give a more random look, I wanted the same animals (the squirrels, for instance) to be placed at different heights moving around the room. So when I started plotting my strips and cuts from the second bolt, I made sure that the creatures landed at different heights from the first bolt. That first bolt and the animals’ positions I called “A” and the second bolt and positions were “B”. I only got four strips out of the “B” bolt.
This meant that any given motif would appear at the same height on the wall only every 9th strip. This would give a pleasing, random look.
The plan was to hang all the strips taken in order from the “A” bolt first, followed by strips taken sequentially from the “B” bolt. Repeat with another “A” and another “B”, and then back to an “A” bolt again.
To be sure, I measured and marked and double-checked everything carefully before I cut anything. Then each strip was labeled … (“2A,” “4B,” etc.)
Working around the doors and windows, the room was divided into four sections. The next step was to get all those strips of paper placed in proper sequential order, standing in queue all around the room – all while figuring the center point of each of those four spaces and plotting which strips would be placed flanking the middle of that wall.
Some cool features of this pattern is that it was placed smack down the middle of the 20.5″ wide strip, which made it a lot easier to center and balance the design than if it had been placed off-center. Also, the design did not reach across any seams, so (other than plotting the height where each critter would fall) there was no pattern match. This made it a lot easier to accommodate crooked walls and un-level ceiling and wainscoting.
The dimensions of the room were also amazingly in sync with those of the wallpaper pattern. Vertically, the 82″ height of each wall / strip worked with the placement of animals on the paper, so virtually all animals were kept intact. There was only one bird who got cut in half at the wainscoting, and that happened only every 9th strip (twice in the whole room).
Horizontally the pattern worked out just as incredibly. The width of all of the walls worked out to be within an inch or two of a multiple of the width of the paper. So centering the strips / pattern on each wall resulted in a look as if the design were “framed” by the door and window moldings. Sorry, no pics.
The downside was, just by happenstance, I ended up with an extraordinary number 1″-2″ strips that had to be squeezed in. Time-consuming and PITA.
I centered the pattern on each of these four wall spaces. But that meant that the rhythm of the pattern would get screwed up as it passed over the door to the butler’s pantry, two windows, and the 12′ wide entry to the hallway.
Here again, the dimensions worked amazingly well, and so did the very accommodating pattern. In the short 10″ high areas over these doors, I was able to “fudge” the pattern by slicing strips vertically along a tree trunk, for instance, and then overlapping the two sections an inch or two, to “shrink” the strip’s width. Making an inch of width disappear from each of seven strips is barely noticeable, and maintains the rhythm that the viewer’s eye wants to see as it travels around the room. Again, sorry, no pictures.
The walls had been primed a few days before; just laying out and hanging the paper took me 12 hours.
I hung this “Indie Wood” pattern by Timorous Beasties on the top 5′ above paneled wainscoting in a new home in the Woodland Heights neighborhood of Houston. It’s made of non-woven material, and can be hung by paste-the-wall or paste-the-paper (which was what I opted to do). Non-wovens are strong and have a high fiber-glass content. They are designed to strip off the wall easily when it’s time to redecorate. Additionally, they are dimensionally-stable – they do not expand when wet with paste. This makes it much easier to plot placement of strips and motifs.
The interior designer for this job is Stacie Cokinos of Cokinos Design.
The Wallpaper Lady's Blog 