Challenges With Moody Jungle Powder Room

Yesterday’s install was quite fun, but there were some unusual or challenging features to the room. Here are some of them.
First, in most areas, the chair rail had a sort of gap between it and the wall, probably then filled in with caulk. I used some craft paint from Texas Art Supply to color that in, so there wouldn’t be white showing between the dark green paint and the black wallpaper.
My usual trim guide (not pictured) is thin, designed to allow you to cut very close and tight to the edge. But in this case, I was afraid it might leave some of that gapped area showing between the paper and the wood trim.

So I used this steel plate tool, which is thicker and would allow me to get a fat cut – just enough paper left to wrap a teeny bit onto that gap area. Note that before I trim, I’m going to press that edge into the corner. I couldn’t hold the camera and hold it in proper position at the same time.
Also, you’ll notice the rolled edge at the top of the tool. That’s thicker, and allows for getting an even fatter cut, for instance, when you want just a tad of paper to wrap around a corner . Do a Search to see my previous post about this technique.

Here I’ve made the trim cut and am peeling away the excess that was trimmed off at the bottom.
See how the bottom edge of the wallpaper now wraps a tiny bit and fills the gap neatly?

Next issue – wall height. On this wall, the height is 3′ + 30.5″

But on the opposite wall, the height is 3′ + 29.75″.
This means that you can expect the ceiling to move up or down, which means that a pattern motif – let’s say one of those cute chameleons – could get his head chopped off by the descending ceiling.

Next issue – bowed wall. Here my yardstick is sitting pretty squarely against this wall, in a corner .

But as I move it up the wall a little further – wow! – that wall takes a dip to the left. And it’s quite a dip! The wall has a bow in it.
I can get my next strip of wallpaper to cover that space. But the fallout will be that pattern motifs will hit the wall at different points, which means that the next piece to be placed after that, the pattern will not match perfectly at all points.

All right. So that previous corner had a bow. This one is out of plumb. Here you see my laser level showing that my wallpaper strip is hanging nice and plumb.

But move the laser to the corner and you see that it’s out of plumb .

Here’s a better example. Again, this causes the pattern to not match perfectly in the corners.

Another shot of the bowed wall, which, for various tech reasons, due to Word Press ‘s crappy New Editor , this shot got out of order and I was not able to place it with the others under the topic.

Papering around the electrical outlet , I had to unplug my light source. There was light coming in from the hall. But this paper, as well as the paint, were so dark that I couldn’t see well to work. Enter my Big Larry flashlight .

Small enough to fit in my toolbox , but really bright and dependable for when you need it.

The pattern is called Fantasy Tree and is by Breeze and was purchased through one of the showrooms in one of Houston’s decorative / design center s. It’s a nice non-woven material , easy to hang , easy to remove , durable and stain-resistant .

What’s A “Fat Cut” ?

Here, I’m hanging paper from right to left, and have just come around a corner , which is in the center of the picture. You almost never wrap wallpaper around an inside corner . Corners are never straight , and the paper will buckle in the corner . And the edge will not be straight , nor plumb , and thus the next strip won’t butt up perfectly against it . And it’s also probable that the strip will torque off either up or down, causing your pattern to creep up or down the ceiling and floor lines.
The answer is to stop the strip of wallpaper in the corner , and cut a new piece for the subsequent wall.
But you can’t just trim tightly to the corner. Because most likely there will be gaps (remember I said that corners are never straight?), so some of the wall will show.
So what you do is wrap the paper just a teeny amount around the corner , and then overlap your new piece over that. This does mean that you will lose some of the pattern in that overlap.
I can’t stand that pattern mis-match, so most of the time, the way I do it, I’ll take a fresh strip of wallpaper for the next strip (to be placed on the left in the photo) and trim it so the pattern matches as perfectly as possible. But I’m getting ahead of myself. Back to the fat cut …
In the photo, I’ve cut my strip on the left 1/2″ wider than needed to fit this wall. I don’t want this 1/2″ of wallpaper under my overlapped new strip, because the leaves a visible ridge. But you do want a little underlap, because you need that to prevent a gap from showing in the corner.
So in the photo, I’ve trimmed off most of that 1/2″ and trimmed it down to an unnoticeable 1/8″. How on earth can you get a trim that thin and that consistent?!

I use this handy metal plate with a rolled edge (on the left).

This plate has bends and other edges of other thicknesses , rounded edges , won’t leave marks on wallpaper, so it has many uses.

Here’s a close up of the trim guide edge that allows for that 1/8″ fat cut .

Back side of the plate. (Don’t mind the blue tape – it’s just there temporarily.)

This edge is a little thinner , and would cut too close for use in a corner. But it does have a use if you need a trim in an area where you don’t want the paper trimmed tightly into the edge / corner.

You’re looking at where wallpaper meets crown molding. This join edge has gaps between the molding and the wall in some areas, and other areas have gunk and uneven areas. Trimming with my usual trim guide would cut too close and let some of these icky things show. So here I’ve used the thicker trim guide. As you can see, it allows the wallpaper to wrap ever so teeny much of a bit, so it covers the bad area, but doesn’t creep onto the molding.

Here’s another example, along door molding. At the top, I used my usual thin trim guide (see below). But this allowed a bit of a gap to show, due to decades’ build up of paint , caulk , dirt , etc.
So, midway, I switched to using the steel plate as a trim guide. This made the cut just fat enough that the wallpaper wrapped a hair and covered the icky area.

Here’s my usual trim guide . I’m guessing it’s about 9″-12″ long .

You can see that the edge is very thin . In most cases, this is ideal, because it allows for good, tight trims right smack into corners and edges.
That steel plate shown above was invented by a colleague in the Wallcovering Installers Association ( WIA ) . They are all the same length, but they come with three different degrees of angles , and can be used for lots of wallpaper installation tasks .
The colleagues has them manufactured and then sells them to us paperhangers . She sells other cool tools , too. If you’re interested in purchasing any of these , or seeing what else she has, go here https://www.facebook.com/customwallpapertools or here https://www.wallpapertoolstore.com/?fbclid=IwAR2NFrG2gWSzNClNMB0gHDiQHbnkhyNhthaOFQaK8MCaU7rBYVQhYQkO0nc
Her name is Eunice , so we call them EuniTools .