OK, never mind the ’80’s-era toilet paper holder that’s recessed into the wall here and is not removable – which presents a challenge all its own. My issue is adding the next strip of wallpaper to the left, turning the corner, and keeping the pattern matched as well as possible in both the inside corner and around the outside corner. Usually, when turning inside corners, you wrap the paper around the corner 1/8 of an inch, and then cut a new strip of paper, match the pattern, and then overlap it that 1/8″ . That helps eliminate issues like mis-matches or wrinkles due to crooked corners or uneven / bowed / out-of-plumb walls . (no walls are ever perfect ) But in this case, we also have an outside corner to wrap. Even though it’s only about 2″ wide, that edge can cause the pattern to go off-plumb , or to create wrinkles in the wallpaper . Going against most rules of wallpapering , I’ve decided to wrap the next strip around this 2″ wide wall and then onto the wider wall to the left . Here I am, starting to position that next strip. I’m not going to try to wrap a full 27″ wide strip around this turn. Instead, I’ve trimmed it vertically along a horizontal stripe , which makes this strip narrower and more easy to handle , and also will help in placement of the next strip. Now I’m pushing it into place into that corner. Note how the paper is wrinkling, both on the wide wall, and as it comes around the 2″ wall. Another shot of the placement and wrinkles . Using my plastic squeegee smoother to press the paper tightly into the inside corner. Note that, since the corner isn’t perfectly straight or plumb, there were a few areas where I couldn’t press the paper tightly into the wall, but had to leave a bit of a gap or air bubble, in order for the left edge to wrap around the turn. The plastic smoother can also be used to gently push out wrinkles on the larger body of the strip of paper to the right. Don’t press too hard , nor overwork , because you don’t want to stretch the paper – that will cause more wrinkles. The plastic smoother took care of the inside corner. Here I’m using my damp microfiber cloth to tightly press the paper around this outside corner . OK. Paper’s wrapped tightly around this corner – but, because the corner isn’t straight , we’ve got wrinkles and warps . Sometimes, you need to take a scissors to make relief cuts to help ease the paper around the corner . Try to make your cuts along an element of the design , to make the slit less noticeable.here is that little narrow bit, finally wrapped around the outside corner. Now we need to add the next strip to the left of this. Note that this narrow strip isn’t straight nor plumb nor equidistant from the corner that we just turned. Nor is it equidistant from the next corner we have to deal with, which is to the left (not pictured). Since we want the wallpaper strips to match in the corners, it’s important that the wallpaper pattern fall in the corner to the left at the same point from ceiling to floor. Complicated to explain. So I’m taking a fresh strip of wallpaper , made sure the pattern matches correctly , and have trimmed it vertically along the tan stripe . Now placing it along this wrapped edge. Because I’m overlapping instead of butting , I’m able to pull the new strip to the right or left, to keep it equidistant from the right outside corner . Or, from the inside corner to the left. Actually, I don’t care much about the right side. The eye won’t notice if the new strip isn’t perfectly plumb . Nor will it notice if the pattern match isn’t 100% perfect . But it will notice if the pattern doesn’t match perfectly in the inside corner to the left. So I’m pulling and manipulating and overlapping the strip a bit, so that the left edge of it is exactly 10-3/4″ from the left edge. This ensures that the pattern motifs fall all at the same point into that corner on the left. Do I can cut my next strip, trim it vertically so the design matches with that in the corner, and get a perfect pattern match in the corner. Kinda difficult to explain, but I hope you can follow what I’m describing. Note that this overlap is causing a bit of a ridge under the paper . Hard to see here, but when the paper dries and shrinks tight against the wall, it will be a little more obvious. But I’d rather have a ridge on the right, than a pattern mis-match in the corner to the left. Oh, and never mind that little pattern mis-match to the right … that’s the paper wrapped around the corner, so you’re looking at different dimensions, not a pattern mis-match. Here is that strip finished. The vertical strips isn’t perfectly plumb, but no one can tell that. ut the pattern is perfectly straight in the inside corner to the left . So when I take my subsequent strip and trim it vertically to remove the right edge by approximately 10-3/4″ , the pattern should match perfectly in this inside corner. (It did!) This “sort of” Greek key trellis geometric design is by Thibaut , one of my favorite brands. It was on a triditional paper substrate , and was hung via the paste the paper method . It was purchased from my favortite source for wallpaper in Houston , Dorota Hartwig at the Sherwin-Williams in the Rice Village , who has more selection books than anywhere else in the city – and knows what’s in every one of them! Call before heading over (713) 529-6515 . The home is in the Champions Forest area of northwest Houston.
Walls were originally a light tan , with a poor texture job , too much caulk along the top of the backsplash , and later it was discovered that someone had painted (several layers ) on top of wallpaper . Same area after I’ve skim-floated and sanded smooth , then primed with Roman Pro 977 Ultra Prime made specifically for use under wallpaper . I have Murphy Brothers paint store add a little blue tint so I can see where I’ve rolled it on. Finished!Such a happy pattern to look at – swirly , nods to foliage and ferns , crisp . Yet not too busy , due to the 2-tone color palate and the tight, overall design .Close up. You get the feel of a watercolor artist / painting .The design matched up perfectly in the last corner . This only happens about once in every 10 years! In addition, what’s even more astounding is that EACH of the four walls in this powder room was EXACTLY the width of two strips of my Serena & Lily 27″ wide paper + expansion. The strips fell in EACH corner ABSOLUTELY tight and straight. I’ve had perfect kills before, but never had paper fall in the corners with no need to wrap or trim. I know that’s a little techy for the non-professional reader to grasp. But just know that it was a room and a day full of almost paranormal-grade coincidences , math , and execution . Pattern is Priano and is made by Serena & Lily , one of my favorite companies. This is the home of a young family in the Spring Branch area of Houston .
Grasscloth is a natural material that cannot be matched from strip to strip, so all the seams will be visible . In addition, there is usually a slight but noticeable color difference between strips / panels (called shading or paneling ) . So it’s important to plot the layout of the strips to give the most visually pleasing overall look. Usually this means balancing the width of strips so they are all equal , at least on the same wall . We call this engineering . This wall presented particular challenges , due to the widths of the elements. Grasscloth comes 36″ wide . You can use your straightedge and a sharp razor blade and trim it down to any width you want. The width of both the large wall spaces to the right and left of the bank of windows was 34.” The width of each window was about 35.” The width of the two spaces in between the windows was 7.” So you’d think I could trim my panels on either side of the windows, and then over the windows, to about 34″-36″ – give or take a few inches (or fractions thereof). But that would leave me with two 7″ wide strips between these 35″ panels. Although the look would be uniform and mirror-image from the center outward, moving from right to left you’d have: 35,” 35″, 7,” 35,” 7,” 35,” 35,” … those 7″ breaks were just not going to look right. One option was to determine the width of the wall (189″) and make each strip an equal width. This worked out to six strips, each at 31.5″ Not good, because this would mean a seam down either far side. And since those sides were 34″ wide, that would mean a 31.5″ wide strip and a strip 2.5″ wide. Not attractive at all, and it would use up an extra strip of wallpaper. This six strips @ 31.5″ wide scenario might also land with a seam smack in the middle of those 7″ wide interludes in between the windows. Not attractive at all. So I decided to make the two outer strips 35″ wide. That left 119″ of wall space above the windows to be covered with wallpaper. Do some math and you get four panels of 29.75″ wide. This gave a balanced and uniform look to the area over the windows, and also prevented seams from landing between the windows. Moving right to left, I cut and hung the full length outer strip first. Then I cut and hung the strip over the window on the right. Then I measured to find the centerpoint of the window in the middle. Turns out it was a bit less than 29.75″ away. So I trimmed that next over-window strip accordingly. Once that was in place, I measured from that center point above the middle window out to where my left full-height panel would fall, 35″ out from the wall. Took the resulting measurement and divided by 2. Lo and behold, each of the next two panels over the window was going to be a bit wider than 30.” No problem. No one (but a paperhanger or maybe an engineer) is going to notice a 1/4″ or even a full 1″ difference in widths between this strips over the windows. Another thing to point out … it’s important that I took measurements before cutting these strips for this second left-hand section. Because, since grasscloth comes at 36″ (and walls can be wonky), if my strips had been narrower (say, 28″), that last full-height panel on the left might have ended up needing to be 37″ wide – and that wouldn’t work because it only comes 36″ wide – plus you need at least 1/8″ to wrap around the corner. Luckily I had the flexibility to be able to trim the panels over the windows to any width needed, to accommodate all this. If you’ve followed all this so far, let me also toss in that we also need to figure how to get paper in between those windows. More on that below. In this scenario, I’m moving from right to left. Area beneath the windows needs to be treated in the same way, and preferably with widths that match what’s going on above the windows. In addition, it’s tricky because after you move across 12′ of wall space, the strips above and below the windows are going to twist and torque out of shape, so that last full-length panel on the far left might not butt up perfectly with the last strip under the windows. The grasscloth is black , and my wallpaper primer is white . It’s common for teeny gaps to appear at the seams . In this case, it’s likely that white wall would peek out from those gaps. So I like to stripe under where the seams will fall with dark (diluted) paint . This takes measuring , plotting , and also a heat gun to get the paint to dry before the wallpaper hits it, to avoid staining. You can do a Search here to read more about this technique . Now let’s talk about getting wallpaper in between those windows. As you can see in the photo, if I hang a 30″ wide strip, a whole lot of paper is going to be cut off and thrown away. Also, a whole lot of sticky, pasted paper is going to bump against that window molding and maybe even the window glass. A lot to clean up! And unwieldy, to boot. My solution was to stop the wallpaper just a little below the tops of the windows. Then I would patch in a 7″ wide strip in between the windows. This is trickier than it sounds, because, if it were a paper wallpaper, I could simply cut along a design motif and overlay the 7″ wide piece. But grasscloth is thick and overlaps don’t look good. Also grass has no design elements , and the reeds of grass don’t necessarily fall perfectly horizontal , and even if you cut everything perfectly true to square , if the window molding is a teeny bit off-plumb , then your edges won’t butt up perfectly. So that’s a good reason for striping the black paint under where the butt join will occur. Same thing for the sections under the windows. I measured and positioned the strips so that the top edge (which I had trimmed to be perfectly horizontal) fell between the narrowest part of the windowsill molding, for less visibility. I admit, instead of butting the two pieces, here I did overlap the 7″ wide strip about 1/4″ onto the piece under the window, right at that narrow junction. It’s only about 3″ wide, and I figured no one is going to be examining it that closely, anyway. This saved me about a half an hour of measuring, trimming, testing, repeat, repeat. This is my second window interlude, and by this time I had realized that it’s hard to trim stiff grasscloth around intricate moldings precisely . So I used paint to fill in the edges around the window molding, just in case there might be any gaps between the grasscloth and the molding, so you would see black instead of the white molding paint. I did this with a small sponge; if I had used an artist’s brush it would have been a bit neater and tighter to the conforms of the molding. But sometimes you’ve gotta relax and realize that no one’s going to be scrutinizing the insides of moldings below shin-level. Area over windows finished, with drapes back in place. Turns out this particular grasscloth is so uniform in color (quite unusual, I will add), that you can’t really see the panels , nor their equal widths , anyway. I’m still glad I took the time to do all this math and trimming. Area below the windows, done. That last seam on the left bears some explanation, too. Moving across the top of the windows, I measured that that last strip – the full-length strip – would need to be exactly 35″ wide. It butted up nicely to the last strip above the windows. But, due to twisting , shifting , expansion , unlevel and unplumb walls and ceilings , and other factors, there is a really good chance that that last 35″ wide strip would not butt up perfectly with the last 30″ wide strip under the window . So I planned to splice these last two strips together. Yeah, the drapes are hanging there, I coulda overlapped the two strips about 1/2″ and the drapes would have covered it. With a thin wallpaper, I probably would have done this. But grasscloth is thick, and an overlap would be visible , and also the adhesive / paste can’t be trusted to adhere as well to grass as it would to paper . So I plotted for a splice. Instead of trimming my last strip under the window to 30″ (read above), I trimmed it to 32″ wide. That way, when I hung the last full-length strip to the left, which was 35″ wide, it overlapped the piece under the window by a few inches. Then I did a double cut and spliced the two pieces. See below for details about that technique. Grasscloth is 36″ wide, and this wall area is wider than that. So two strips were needed. This means you’re going to have a seam, and since grasscloth seams are always visible, it looks best to plot to have the seam fall down the center. It uses more wallpaper to do this, but it looks much better than having, for example, a 36″ wide strip next to an 8″ wide strip. As mentioned above, in case you get thin gaps at the seams, a dark stripe of diluted craft paint under where the seam will fall, will prevent white wall from showing through. Rounded / bull-nosed edges and corners have been popular in new construction for at least 10 years. I wish they’d go away. They’re very difficult to trim around, and hard for the paper to conform to and adhere to. It’s very hard to trim around that rounded edge, because the paper is hanging over and blocking your view, because grasscloth is thick and stiff and your fingers can’t feel through it, and because the edges aren’t necessarily true and plumb so a laser level or other level won’t help you much. I use this little gadget as a trim guide. It’s actually a small section of the same corner bead material that drywallers use when they assemble these walls. Cut to about 1″ long and notched in different places where you might trim along the edge of the wall. It’s intended that you place your trimming knife in one of the notches and slide the gizmo along the edge and make your cut. I find that awkward and also inaccurate. So I prefer to use the notches as a guide and mark where I plan to trim with a pencil. Since this wallpaper is black, I used this marking pencil from my home sewing kit instead. Chalk might work, but I was afraid it might now wipe off completely. The pink pencil line was barely visible, but it was enough for me to use a scissors to trim along the grasscloth. I like this better than using a razor blade as I can see better, and also less chance of scoring into the primer or wall. Which raises its own set of issues – do a search here to find previous posts.Inside view of the trim guide. Finished arch. Note the four panels of equal width above the arch. And two flanking full-height panels also the same widths. I was lucky that there was no pattern to match, so I was able to butt my two flanking strips right up to the edge of the bull-nosed corner. No trimming needed! Then I measured the remaining width between these two strips (the area over the arch), divided by four, and cut four strips of equal widths. I hung the two on the left, and then one on the far right. This left one strip still to be positioned to the right of center. So the pieces are going to meet over the arch, rather than the last strip falling in a corner. Same as the last strip under the window (discussed above), it’s really difficult to get your last piece to fit in here perfectly. I’ve done it, but it takes a lot of measuring, trimming, testing, retrimming, and often starting all over again. So I did a double-cut / splice. A double cut involves cutting each strip an inch or so wider than it should be, and overlapping the two. Then you take a straight edge and sharp razor blade and cut through both layers. This handy tool is a wonderful non-slip guide for this process. It was invented by an installer colleague in the Wallcovering Installers Association ( WIA ) and she has them fabricated in various lengths (along with other cool tools ) and sells them on-line. Contact me if you’re interested. Anyway, it takes a lot of strength to cut through two layers of grasscloth, so somewhat difficult for lil’ ol’ me. You also want to be sure to not cut / score into the wall, because the tension of drying wallpaper can tug at the wall and cause it to actually come apart, leaving an open seam that’s difficult to repair. So you’ve got to put some padding under the wall where the cut will take place. I use special strips of polystyrene (hard but flexible plastic) to pad the wall. Also invented by a colleague in the WIA , who also sells other cool tools and supplies. Contact me if you’re interested. This black grasscloth was printed on a white substrate. If the seams aren’t absolutely tight, there can be worries about the backing showing through to the front. So sometimes we’ll take a piece of chalk or pastel (never oil pastel or permanent markers because they bleed and stain ) and run it along the edge of the paper – from the back, and taking care to not get chalk on the surface. I do this frequently with dark papers ( do a search here to see previous posts ) but opted not to do it with this grasscloth. It wasn’t necessary, and might have stained the porous reeds of the grass. It was beneficial, though, to have striped dark paint on the wall under the seams, as mentioned above. Ugh. Grasscloth comes 36″ wide, and this section of wall is 38″ wide. It’s not visually pleasing, nor is it easy from an installation point of view, to have a 36″ wide strip next to a 2″ wide strip. Or to use scraps and put a 25″ wide strip next to a 13″ wide strip. So best to plan two strips of equal widths. Two strips, each 19″ wide, with the seam down the middle. Actually, the strip on the left was 19″ wide, but I trimmed the strip on the right to 21″, because I like the wallpaper to extend 2″ over the top of the door molding. This provides a more stable surface in case of shifting foundation or walls, and less likelihood (knock on wood) of the seam opening up should the house / drywall experience shifting. Note that design “rules” caution against seams down the middle of spaces. But it would have been more visually distracting (and used up more paper) to have made three strips of each 12.75″ wide. And would have looked even dumber to have used scraps left from other walls and put together two strips of disparate widths. So the homeowner and I discussed during our initial consultation , and she was happy with the center seam. Once it was all finished, this particular grasscloth was so even in tone that you barely see the seams, anyway. Win-win! This did use up additional paper, though, as noted in a previous photo above.
My “after” full-wall photo didn’t turn out, so you’ll just have to look at the close-up shots.
From a distance, this small, tight pattern with subtle movement looks like a textured wall. It forms a comforting backdrop to the furnishings and activities in this large central area in the home.
This is a clay-coated, hand screened print, and is made by Relativity, a small outfit operating out of Chicago.
The Wallpaper Lady's Blog 