Dining room before. This bungalow in the Woodland Heights neighborhood of Houston is very true to the Arts & Crafts / Craftsman period. This style featured straight , clean lines , nature , and muted colors that mimicked those found in nature . The homeowner is a retired woodworker / carpenter and did much of the millwork you see here. Done. The teal green is actually a little more muted than the photo shows. From another angle. Close-up. This wallpaper pattern is called Fir Tree . A frieze is a wide wallpaper border , usually run around the middle or top of a room . The manufacturer is Bradbury & Bradbury . They specialize in period-inspired patterns from past eras, such as Victorian , Arts & Crafts , Oriental , Modern Age / Mid Century Modern , and more. Bradbury prints on stock that’s about 28″ wide, and this border is about 13″ wide. So Bradbury prints two borders side-by-side , and then you need to use a straightedge and razor blade to cut them apart .Although the border came about 13″ wide, the space between the beams was only about 11.5″ . So we were going to lose about 2″ . I consulted with the homeowner. He really wanted to see the copper metallic pine cones. We also felt the trunks of the trees were important design elements . We decided that the pattern could afford to lose more from the top , which would permit more of the tree trunks to show, all the while preserving those pine cones. Here I am trimming 2″ off the top, so the overall height of the frieze is now 12″ . That will fill the space between the beams, and also allow a little bit to tuck down below the bottom beam (there is a gap between the wall and that beam). The room was really dark , the wallpaper was dark , and my straightedge was casting a shadow where I needed to trim. So I grabbed my Big Larry flashlight from my toolbox and was able to see where to trim. Bradbury uses inks that are quite delicate , and can be scratched or marred simply by brushing with my smoother brush , or my plastic trapezoid squeege smoother tool . Metal – like a trim guide or scissors – will also leave marks on it . Here I’ve wrapped tools in microfiber towels and baby socks , to soften contact with the wallpaper . Bradbury inks and substrates can be finicky, and it’s important to use the paste recommended by the company for the particular colorway that you’re hanging . In this case, I had to use clay – based paste . The inks and substrate aren’t always compatible , so when you add wet paste to the back , it can cause the substrate to absorb moisture and swell , while the inks on the surface are holding tight. This will result in wrinkles , warps , and bubbles on the surface . We call this quilting or waffling . One trick is to lightly sponge clean water onto the inked surface. This will allow the surface to absorb moisture and expand hopefully at the same rate as the backing , hopefully eliminating wrinkles and bubbles . On this install , I still had problems with uneven expansion . And with the paper drying out before I could get an entire strip up on the wall. So, while I was pasting the back, I also sprinkled a little water on the back and mixed it in with the paste . This did seem to even out moisture , and also help the material remain moist and workable during the installation . In addition, I also had trouble with the edges of the paper drying out before I could get a full strip up on the wall. Part of this was because it’s winter time and the furnace was blowing hot air into the room and drying out the paper. My counter-attack was, again, to sprinkle a little water onto the back, to hydrate the material more. Also, once I had pasted a strip and rolled it up (see below), I dipped the edges into about 1/8″ of clean water. And then wrapped the pasted material in a plastic trash bag and allowed to book for a few minutes before hanging . This is standard procedure with wallpaper. Actually, what worked better was to paste, book, bag, and then just before hanging to dip the ends into water. This seemed to keep everything wet and workable better and longer. Despite all this, some small bubbles did remain in the paper. As the paper dried, though, they flattened out. When you book a strip of wallpaper, customarily you fold the top 1/3 down and the bottom 2/3 up. This keeps paste from smearing all over everything, and makes each strip shorter and easier to handle. And allows you to get the top section of the pattern lined up with that on the previous strip , before unfolding the bottom section and working that against the wall. But it’s a little different handling a narrower border that’s maybe 12′-15′ long. What I do to make this manageable is to book the material in accordion pleats . See photo. Then I can unfold just a small section, work it into place, and then move along the strip, smoothing just a small section at a time against the wall. Actually, with this install, I positioned my sections against the wall temporarily, to get the whole 15′ strip up there. And then went back and smoothed each section against the wall, working out bubbles and warps , and ensuring that the frieze was pressed tightly against the wall at both top and bottom . There were four strips around the top of this dining room. On each strip I used a different install method. By the time I was done, I had learned how the material wanted to be treated. The homeowners are in love with this period-authentic look for their vintage bungalow. The husband said it was like Christmas, because they had waited for so long to have this room completed, and now it’s finally finished and beautiful!
The rich colors and clay coating give this wallpaper a truly luscious , velvety look. But they’re also fragile and can be damaged easily . Here you see damage caused at the factory simply by folding back the last 2″ or so of paper, before rolling it up. The company does provide and extra foot or two to accommodate this. You have to be extremely careful handling this stuff. Even a fingernail or your wallpaper tools can cause scratches or marring . Per the manufacturer’s suggestion, I covered my smoothing brush and plastic smoother with microfiber towels , to minimize chances of scratching the paper . In fact, the manufacturer suggested that, during installation , that you wipe the entire surface uniformly with a damp microfiber rag , to even out any imperfections that might have resulted . Now, just between you and me – if you know you have a product that’s likely to end up with blemished areas, why not just switch to a better , tried-and-true ink ? SMH Luckily project this is a border that will be butted up under the ceiling , so no one’s going to zero in on a few shiny areas in the matt ink. But , think of all the homes that will have this same material as a wall paper , that will be viewed close-up . Not all colorways from Bradbury do this. I’ve hung plenty of it and not had a problem with most. In fact, the “fishnet” area you see at the bottom of this picture is not delicate at all. It’s the very matt finish green and brown colors in the center of the border that are so delicate . The inks and clay coating the manufacturer uses on this particular colorway are very fragile and mar easily , so I’ve used ankle socks to cover the edges of my straightedge, and also a weight I’m using to prevent the paper from rolling around on my table. And that scissors is just there as demonstration for the photo … you can bet that tool was not touching the surface of the border at any other time. This material has a selvedge edge that has to be trimmed off by hand , with a straightedge and razor blade . Normally I set my straightedge on top of the wallpaper , because it’s easier to see where I need to make my cut , and also because the weight of the straightedge helps hold the wallpaper down. But even with cushioning socks on either edge of the 6′ long tool , and with padding on the underside, I was afraid that it might harm the inks . So I placed it on the outside edge of the wallpaper. This left very little for the tool to grab on to, so I made sure to press it tightly against my work table , so the wallpaper strip wouldn’t slip around while I was trimming . The manufacturer is Bradbury & Bradbury . They specialize in historic and period-correct patterns from the 19th and early 20th centuries.
Mural panels standing on edge are cut, sequenced, staged, and ready to be pasted. The panel lying on the floor will be my last strip, and will need to be measured and trimmed narrower before it’s ready to be pasted or hung. I use several different methods to paste pre-pasted wallpaper, and you can do a Search here to read more. But for today, I’m using the tried-and-true historic method of running the strip quickly through a water tray . At the top of the photo, several strips have already been submerged and pulled through the water, then folded pasted-side-to-pasted-side. This is called booking . Booking allows the adhesive on the back of the wallpaper to absorb the water and become activated. And it allows the wallpaper substrate to absorb moisture, expand, and then contract a little. This method can sometimes get the material a little too wet, which can lead to over-expansion and then bubbles on the wall. That’s why I’ve placed the booked strips at a slant and over the bucket – so excess water can drain off. Usually I paste and book one strip and then paste and book the next strip. While I’m hanging one, the second one is booking and waiting its turn to be hung. But with this water tray method and certain brands of pre-pasted material, such as Anewall , York , or Sure Strip , the paper sometimes gets so wet that it needs more time to dry before attempting to hang. So I’m pasting more strips at a time, so they can be drying out a bit while I hang the first strips. There’s a bit of a risk to this, which is the potential for the paper to over-expand as it sits wet waiting to be hung. Then once it’s on the wall and starts to dry, it can shrink. All wallpaper shrinks when it dries. But if it has expanded too much, then when it dries and shrinks, you can be left with small gaps at the seams. Again, gaps are common with all wallpapers (most all), but can be exaggerated when dealing with over-saturated pre-pasted material as it shrinks. Back to the method … You see the water tray, filled 3/4 full with clean water. I’ve set it on towels, which are in turn set on top of a thick plastic clear shower curtain. And that’s on top of my usual dropcloths, which are absorbent on the top (blue) side and water-proof on the underside. All this keeps any splashed water from getting onto the clients’ floors. I also sometimes set the water tray in a bathtub, with towels set over the edge of the tub and on the floor.
The Wallpaper Lady's Blog 