Whimsical Arabian Nights Dance in Powder Room

You’ve got to look at this close-up, to notice the antelope and flames / foliage .

You gotta make a decision … The light sconces (they are currently removed, but you can see the electrical boxes where they will be placed) were centered on the vanity top, but the faucet was off-center by about an inch. So I chose to center / balance the pattern on the sconces and countertop. The mirror will be hung between the two light fixtures, so we’ll end up with a pleasing, balanced look. The faucet isn’t exactly in the middle of the design motif, but no biggie – there’s going to be a mirror there, anyway.

t

Corner going around shower. Note the window looking into the shower.

Although the website specs said this is a pre-trimmed non-woven material , that was incorrect. Turns out it had an unprinted selvedge edge that had to be trimmed off by hand . Here I’m using my straightedge and razor blade to remove this selvedge. This takes precision and a LOT of time .
The manufacturer usually provides trim guides to help you know where to cut. But it’s usually better to trim to the pattern – determine an element in the design motif that will meet up with the corresponding motif on the opposite side of the strip when the strips are hung on the wall, and use that as your guide . Be sure to trim off the trim guide marks, or they will show on the wall.

The pattern is called Arabian Nights and is by Relativity Textiles . I’ve never worked with this brand before. I was not pleased . In addition to the incorrect information about the pre-trimmed paper , the mfgr’s specs said this was printed on a non-woven substrate . It was not. It wasn’t even printed on standard wallpaper stock . Instead, it was a pulp material – This is a sort of old-fashioned wallpaper , and is very brittle and prone to tearing and dragging (your trimming knife or razor blade will get snagged and you’ll end up with a ” chewed ” jagged cut, instead of a crisp cut . It also tears easily. It also has no coating, so it’s not stain-resistant … Not good in a busy household with a 3-year old toddler , or anyone splashing water or soap or air freshener .
It was also difficult to hang . Applying wet paste to the backing causes the substrate to absorb moisture and expand at a different rate from the ink on the surface. So you end up with wrinkles , waffling , and quilting .
Sponging a light bit of water on the front before pasting helps even out the moisture differential and ease installation . I’ve never before encountered a pulp that had this type of ink on the surface. One clue for this bad stuff is when you open the package and it smells like moth balls . Once I figured out how to work with it, , it went OK – although tedious . The seams did look very nice.
BUT … all this effort would have been unnecessary and the finished room would be more durable if the mfgr had printed on a non-woven substrate (as their on-line specs stated) and had used standard inks instead of this weird , smelly , high-end stuff. In fact, the material would have cost the homeowners a whole lot less $ if it had been normal ink on a non-woven backing .
The home is in the Woodland Heights neighborhood of Houston .
installer

Geometric Grasscloth in Home Gathering Area

No, this large room with sink and counters isn’t a kitchen. The family loves to entertain both family and friends, so included this “bonus” room in their new home’s plans. It’s used for both entertaining and crafting.
The wall facing you was originally painted a semi-gloss navy blue. In the photo, I’ve applied my wallpaper primer.
It will adhere to the glossy paint, and provide a matt finish for the wallpaper paste to grab ahold of.

Taking measurements and plotting the layout.

This paper has a selvedge edge , which has to be trimmed off by hand with a straightedge and razor blade. The manufacturer has not provided trim guide marks , so I am using a ruler and my eye.

The new look is so dramatically different I couldn’t resist taking a photo mid-hang. As you can see, I’ve used dark paint to stripe under where the seams will fall, to prevent any of my primer from showing through at the seams.
You can see the ceiling line starting to track upward on the right portion. More on that below.

Finished. Perfectly centered.

This is the mounting hardware for the big screen TV . I asked them to remove the TV, but we left the mounts in place. In order to support the heavy TV, they are placed quite securely into the wall , and I feel it’s best not to jimmy around with that.
Rather than have the first strip straddle the TV mount, I plotted to have my first seam fall down the middle of the wall, placing a seam in the mid point of the mount. This meant I had to hang four strips instead of three, but it made it a whole lot easier to work around the TV mount, as well as to keep the left and right edges of the grasscloth straight and plumb.

Close up showing the texture of this grasscloth material. It’s atypical to have grass cloth printed with a pattern , and I rather like the way the ink looks somewhat scratchy against the rough background.

Because it’s Schumacher, you can expect printing defects . The slight pattern match doesn’t bother me, as there were many more places along each strip that matched up perfectly. Nor do I mind the different intensity of ink on the two strips. That’s all part of the look of grasscloth.
But I wasn’t pleased with the white ink out in the middle of nowhere, as seen about 1//3 down the center of the picture. This isn’t considered a defect , and from a distance it’s not really noticeable. But it bugged me.

So I used some water-based paint and a very small brush from the craft store and lightly touched up the spots.

I also softened the mis-matched edges a bit. There’s a fine line between covering the white spots and staining the material, so use a light hand. And never permanent ink or oil-based markers or pastels.

Likewise, the ceiling line was not level, so as I moved from the mid-point out to the right, the ceiling rose above the geometric motif’s top edge, and a white line began to be visible, but only to the right of the centerpoint.

So I used the black paint to cover up that extra bit of white. This increases the width of that horizontal navy blue line from 1/4″ to about 1/2″. But from down on the floor you can’t tell, and it looks a whole lot better than having white on the right side and none on the left.

The brand is Schumacher and the home is in the Garden Oaks / Oak Forest area of Houston.
The interior designer who came up with this bold and lively look is Clayton Brooks .