Kill Point Over Door

aaHere’s what this flowing viny wallpaper pattern looks like in this dining room in the Garden Oaks / Oak Forest neighborhood of Houston . The bottom 1/3 of the wall is block paneling / wainscoting , so the wallpaper on just the area above is not overwhelming .
A kill point is the place in a room where your last strip of wallpaper meets up with the first strip you hung . this virtually always results in a pattern mis-match . So we try to hide that in an inconspicuous place, such as in a corner behind a door .
In this room, all of the corners are very visible . A mismatched corner of 7′ high would be very noticeable .

So in this room, I was able to cleverly disguise the mis-match in a much shorter area, over a door . This is only 6″ high . Here my first strip is on the left, and my last strip is on the right, with two short strips needed to bridge that gap .

Here the strip on the right has been put into place.

Here’s the piece that will butt up against the strip on the left. Eeek! It’s 1/2″ too narrow to cover the gap. Also, as you can see, there is an obvious pattern mis-match at that seam on the right.

look at this tree branch . I’m going to use that to my advantage.

Here I’ve taken another piece and have matched the pattern on the right side. Note that it’s not matching on th left.

Here I am, back to that strip we saw a few photos ago, that will match with the strip on the left. Remember tha tree branch I pointed out? Here I’ve trimmed the wallpaper vertically along that tree branch .

Here I’m putting it into place, butting it up against the strip on the left, and overlapping the strip on the right. But that’s going to leave a vertical ridge under this strip, where the strip underneath it ends on the left.

But you won’t notice that overlap if it runs under a design motif . Here I’m using a pencil to trace the outline of that tree branch, bringing it in so that the tree branch will overlap just 1/8″ – 1/4″ over the strip on the right.
Note that since the surface of this paper is vinyl , and wallpaper paste doesn’t always adhere well to slick plastic , I’ve used a special border paste or vinyl over vinyl or seam repair adhesive just on this small 1/8″ overlapped area .

Strip on the right trimmed to conform to the curves of the tree branch.

Tree branch piece being put into place.

Tree branch strip trimmed and finished.

SDone and viewed from below. OK, so the pattern doesn’t match 100% perfectly the way the designer intended. Some of the motifs are closer together than they “should” be. From here, who the heck is going to notice?! This looks pretty darned good – and it looks way better than having a 7′ long mis-match in a very visible corner .

The pattern is called Twining and is by Graham & Brown . It has a very light texture , and also a slight
metallic sheen on the branches . It’s a non-woven / paste the wall material , and will strip off the wall easily and in one piece when it’s time to redecorate . I like their papers a lot .
You can purchase G&B from Dorota at the Sherwin-Williams in the Rice Village . Call first, as hours vary. (713) 529-6515 .
Here’s another cool thing … Go back to that first photo. Since I started hanging paper by centering the pattern between the two windows on the wall to the right (not visible in the photo), by the time I worked my way around to the wall between the windows you see in front of you, the pattern was not going to be centered in between the windows. I thought it would look better if it was balanced symmetrically. So I positioned the dominant part of the tree branches in between the windows. And then I used the same overlap-and-disguise trick over the window on the right.

Outsmarting Bull Nosed / Rounded Edges / Arch

Looks nice, huh?

But these rounded edges , especially arches , have been a thorn in the side of wallpaper installer s since they became popular more than 10 years ago. Hanging paper on them and trimming neatly at the right point is difficult. Because the paper is hanging over the edge blocking your view of where you need to trim . A level or laser level don’t always work because the home’s framing isn’t always perfectly plumb . Metal straightedges / trim guides are useful, but can slip and mess up your cut. The arches present their own challenges because a straight edge won’t line up with them .

A colleague in the Wallcovering Installers Association ( WIA ) invented this gadget , which is a huge help. This is a 1.5″ section cut off from the 10′ length of bull nose corner bead used in the drywall construction of these edges. Then you cut notches in it at the point on the corner where you want to trim your wallpaper .

Some installers place a trimmer blade in the notch and slide the gadget along the edge, trimming as they go. I find that the thing wobbles too much for an accurate trim, plus it’s difficult to hold the blade while you’re sliding the thing down the wall. So I put a pencil point into the notch and draw a line along where I want to trim. Then I can use a straightedge and trimming blade , or a scissors, to cut along the line. Makes a nice, even, straight cut! Note that I like to wrap it about 1/3 of the way around the rounded edge.

OK, so you’ve seen how I trimmed along the edge to the right. Now here’s another trick that I’m going to use on the edge to the left, as seen in the photo. The wallpaper strip is 20.5″ wide. But I trimmed it vertically so that the piece over the arch is 10″ wide. That correlates to the point where I want to trim the strip that will land on the rounded edge going down the wall.
Note that I have not completely trimmed the part under the arch on the left side, because I want to be sure the cut edge lines up with that on the next strip I’m going to hang.
The blue plastic tape is there to keep paste off the wall paint . It will be removed after the piece is trimmed to fit.

Now here I’ve placed the remaining 10.5″ wide left section of the strip of wallpaper. You can see how it’s falling perfectly along the bull-nosed edge – saving me from having to use a blade or straightedge or gadget.
Note that this works only if the edge is perfectly plumb , and that the piece above the arch is also perfectly plumb, and my new strip is hanging perfectly plumb. This paper is a non-woven material, and is somewhat stiff and unbending , so not really amenable to twisting or tweaking into place. Plus, you want to keep that left edge straight, because your next / subsequent strip will need to butt up against it. Trust me, I did a lot of measuring and shooting the laser level before I pasted or hung any paper!
Now that it’s in place, I can go back and trim that remaining bit under the arch, making sure that it meets up in the corner with the edge of this piece .

Here’s another shot of it finished.

Closer up.

This tree branch foliage pattern is called Twining and is by Graham & Brown . I like most everything they make. The non-woven substrate is designed to strip off the wall easily and in one piece , with no damage to the wall , when it’s time to redecorate .
This home is in the Oak Forest / Garden Oaks / Heights neigborhood of Houston .

Subtle Colors , Gentle Movement in Dining Room

Kinda bland, huh?

Well, let me fix that for you!
With just two colors and a simple, yet flowing design, this wallpaper pattern breathes life into this room – but doesn’t overwhelm.
Pattern is nicely centered between the windows.

This is another wall that also has two windows . I was able to center the pattern between these windows, too. Centering on two different walls in the same room is actually something of a feat – but that’s a story for another time.

From a distance .

This home has bull-nosed / rounded outside corners and edges, as well as the arch . Very tricky to get wallpaper trimmed to these areas neatly and evenly . See other posts for more info on this.

Close up. The design has a weathered fabric texture sort of background . The copper colored foliage is lightly metallic , so has a slight shine – but only when viewed from certain angles , so it’s a subdued luster that’s added to the room .
Note how the coppery color coordinates with the light fixtures / chandeliers .

The wallpaper is by Graham & Brown , a good manufacturer with quality papers. The pattern is called Twining . This company makes nice non-woven papers , which have a polyester content which makes them stain-resistant and durable . They are also designed to strip off the wall easily and in one piece and with no damage to your walls when it’s time to redecorate . G&B ‘s materials are usually flexible and nice to work with – although this particular one did tend to drag and tear when being trimmed – even with a new blade. I usually paste the paper , but non-woven materials can also be installed by paste the wall .
The home is in the Oak Forest / Garden Oaks / Heights neighborhood of Houston .
This project took me three days, to smooth the textured walls , and then hang the paper around four walls , and trim around those pesky rounded edges and the arch .

Using One Strip to Cover Two Areas Saves Wallpaper

This wallpaper is 20″ wide . My next strip to the left needs to be 20″ wide above the window – but only 1.5″ wide down the side of the window. I hate to use a whole 6′ long strip for this area. Because, as you can see, most of the strip will be where the window is, and will be cut off and thrown away.

But here’s a plan. The same thing is happening on the right side of the wall, on the window to the right. About 10″ of the wallpaper has extended over the window, leaving about 10″ of the lower portion to be cut off and thrown into the trash.
NNo! Since I need a 1.5″ width of a right edge to finish my area on the left side of the wall (see previous photo), I can use this discarded lower 10″ of wallpaper to cover that 1.5″ to the left.

Planning ahead and measuring carefully, I removed the lower section of wallpaper that would have been hanging over the window / shutters . I left plenty of overlap to allow for trimming along the top and along side the window molding. Added bonus – because I’m now not wrestling a 20″ wide strip of paper next to this window and shutters, it keeps a lot of paste from slopping onto the window molding and shutters .
zin this photo, you see the 10″ wide strip I’ve removed. And also the 1.5″ wide strip from the left right edge, that will be put against the strip to the left.

Here’s my 1.5″ wide strip.

And here’s where I’m going to put it. Note that I cut a short strip to fit over the window . It’s 20″ wide – the width of the roll of wallpaper . I cut it long enough to come down the side of the window to where there’s a design element – in this case, a horizontal branch – to disguise the juncture of these two pieces of wallpaper .

About to go into place .

Positioned. Note the overlap of the branch, trimmed along the lines of the motif. This makes the overlap way less noticeable than a straight horizontal patch, or even a splice.
Note: I don’t like to splice / double cut in situations like these – cuts into the wall surface below and can cause the paper to come away from the wall. I don’t mind overlaps in these situations. They’re up high where no one can see, and also much stronger and more stable than a butted edge .

Teimming off excess along the window molding / trim .

Doone!

The tree and leaf pattern is called Twining and is by Graham and Brown . Like most of their materials, it’s a non-woven material and can be installed by pasting the wall – although I usually paste the paper . It is designed to strip off the wall easily and in one piece when it’s time to redecorate . The seams are invisible .