Wallpaper Inks Easily Marred

The rich colors and clay coating give this wallpaper a truly luscious , velvety look. But they’re also fragile and can be damaged easily . Here you see damage caused at the factory simply by folding back the last 2″ or so of paper, before rolling it up. The company does provide and extra foot or two to accommodate this.

You have to be extremely careful handling this stuff. Even a fingernail or your wallpaper tools can cause scratches or marring . Per the manufacturer’s suggestion, I covered my smoothing brush and plastic smoother with microfiber towels , to minimize chances of scratching the paper .
In fact, the manufacturer suggested that, during installation , that you wipe the entire surface uniformly with a damp microfiber rag , to even out any imperfections that might have resulted .
Now, just between you and me – if you know you have a product that’s likely to end up with blemished areas, why not just switch to a better , tried-and-true ink ? SMH Luckily project this is a border that will be butted up under the ceiling , so no one’s going to zero in on a few shiny areas in the matt ink. But , think of all the homes that will have this same material as a wall paper , that will be viewed close-up .

Not all colorways from Bradbury do this. I’ve hung plenty of it and not had a problem with most. In fact, the “fishnet” area you see at the bottom of this picture is not delicate at all. It’s the very matt finish green and brown colors in the center of the border that are so delicate .

The inks and clay coating the manufacturer uses on this particular colorway are very fragile and mar easily , so I’ve used ankle socks to cover the edges of my straightedge, and also a weight I’m using to prevent the paper from rolling around on my table. And that scissors is just there as demonstration for the photo … you can bet that tool was not touching the surface of the border at any other time.

This material has a selvedge edge that has to be trimmed off by hand , with a straightedge and razor blade . Normally I set my straightedge on top of the wallpaper , because it’s easier to see where I need to make my cut , and also because the weight of the straightedge helps hold the wallpaper down.
But even with cushioning socks on either edge of the 6′ long tool , and with padding on the underside, I was afraid that it might harm the inks .
So I placed it on the outside edge of the wallpaper. This left very little for the tool to grab on to, so I made sure to press it tightly against my work table , so the wallpaper strip wouldn’t slip around while I was trimming .

The manufacturer is Bradbury & Bradbury . They specialize in historic and period-correct patterns from the 19th and early 20th centuries.

From Dark and Dated to Light and Livable

Oh, my! – I hung lots of these chintz florals, ” satin ” look (the design of the dark green at the bottom of the wall), and dark colors back in the ’90’s . Sure enough – this home was built and wallpapered in 1994.
IIt’s still a good look, IMO, and the homeowner still likes it. But she’s just gotten tired of it. So – time for an update !
She also decided to eliminate the chair rail , so the new wallpaper will go ceiling to floor . Here you see some damage to the drywall where the chair rail molding was removed .

What a change! Now the room’s look is quiet and fresh .
The buffet , topped with a decorative mirror , will go on this wall . That’s why I centered the pattern in between the windows , so it will fall evenly on either side of the furnishings .
I also plotted so that a full “Moroccan lantern” (that’s what this style of trellis pattern is called), would balance out between the crown molding and the window molding. There were several of these 12.5″ high areas all around the room, so this placement of whole “lantern” motifs gave the room a pleasing look.
It also worked out that the lanterns were evenly placed and kept whole between the crown molding and the baseboard. See the second following photo to see what I’m talking about
As a note – just this one window wall took me about five hours to measure , calculate , and hang . Getting the pattern to go over, around, and under the two windows , and still line up and match correctly , took some time and futzing. The material was thick and stiff , and a bit tricky to fit into corners and trim around the decorative window molding .
In the foreground you see my work table area . The homeowner has let me put protective padding on her dining room table and then set my work table on that. This saves space and allows plenty of room for my ladder and other tools as I work around all four walls.

So that I could center the pattern on this wall , I had to start hanging my first strip in the middle of the wall. I was lucky this time, that the pattern was centered exactly on the edge of the wallpaper roll . Sometimes (as in the one I did yesterday – see previous post ) the center of the design motif is a to the right or left of the edge of the wallpaper . This, naturally, means you’ve got to do more measuring and plotting and double-checking , to be sure the center of the design falls down the center of the wall .
Back to the photo above … that dark block on the right side of my work table is my laser level. It’s shooting a perfectly plumb red line onto the wall. Here I’m lining up my first strip of paper butted against this red line .
Switch topics … Back in 1994, the original installer did a very nice job of hanging the wallpaper. But … he didn’t prime the new drywall first. That lack of primer / protective layer means that the wallpaper will actually bond to the drywall. I tried, but was unable to get the existing wallpaper off . Eventually, you need to factor in time , damage to the wall , paste residue left on the wall, and take a different tac if called for.
So I skim-floated over the seams , so they wouldn’t show under the new paper , and also floated over the damaged drywall where the chair rail had been removed . Sanded smooth , and then primed the patched areas as well as the original wallpaper, with Roman Ultra Prime Pro 977 . This stuff will adhere to the light acrylic (slick) surface of the original wallpaper, as well as protect it from moisture from my paste on the new wallpaper. ( Moisture could cause the underlying original wallpaper to expand , creating bubbles that will look bad, or loose areas that will pull away from the wall, creating a bubble or pocket.)
My primer is also lightly pigmented, so it helps block out the dark color and busy pattern of the original wallpaper . This particular new wallpaper is quite opaque , but not all of them are, so a pigmented primer is important , IMO .

Left corner of the buffet wall. Here you can see how the lantern motifs are placed between ceiling and floor.

The background has a lightly mottled effect, that mimics grasscloth a bit, and also adds more depth and warmth than just a plain solid color .

Been havin’ more than a fair share of defects lately, especially this week. This paper had on both front and back sides, incidences of these black flecks . They seemed to be maybe charcoal , so I wasn’t too worried about their black bleeding through to the surface , like ink or any oil-based substance will do.
Most of them were embedded in the material itself, so could not be wiped off , nor dug out with a razor blade . Some I had to cut around and discard the affected paper. Others were so small as to not be noticeable once the paper was up on the wall and all the furniture and artwork was back in the room.
There was also one 3′ section of wallpaper that had an odd streak or arc running across it. It wasn’t ink . It was more like some kind of compromise to the substrate . I noticed it was I was pasting the back of the paper . I turned it over and, sure enough, you could see it a little on the surface. (see photo in previous post) It’s the kind of thing that was subtle, but would catch your eye when looking at the wall from a distance . It was minor , but I discarded that strip . Good thing I have the homeowners purchase a little extra wallpaper .

The manufacturer is Designer Wallcoverings , which is a good quality brand (aside from the printing defects I described earlier ). It was a non-woven / paste the wall material , which is pretty user-friendly . It will strip off the wall easily and in one piece when you redecorate . Stain-resistant , and ” breathable ” in humid conditions .
The home is in the West University neighborhood of Houston . Dining room installer

Soft Textured Foliage Brightens Entry

The homeowners knew they wanted something brighter for their entryway . But their paint samples tested on the wall were falling flat.

Wallpaper was the answer! Brighter and more personality and interesting than paint of the same color .

Here’s a better shot showing the actual color .

And here it is with my 100-watt light bulb gone and the room’s chandelier providing the light .

This is a stringcloth material . Note that, just like grasscloth , another natural fiber material , you will see the seams a bit. On this one, the heavy inked areas of the white berries showed more than the background areas . From a few feet away, none of this was visible.

Close-up showing the texture of the strings and the thick ink .
I do think this will have some sound-reduction qualities ( absorb noise ).
Also a note … cats and even dogs love to scratch or chew textured fibers like this.

Rolling it out on my work table. The rolls / bolts were really heavy .

Made by Wallquest in their EcoChic line.
The home is in the Tanglewood / Galleria area of Houston .
installer